Abstract:Direct conversion receiver (DCR) architecture is a promising candidate in the radio frequency (RF) front end because of its low power consumption, low cost and ease of integration. However, flicker noise and direct current (DC) offset are large issues. Owing to the local oscillator (LO) frequency, which is half of the RF frequency, and the absence of a DC bias current that introduces no flicker noise, the subharmonic passive mixer (SHPM) core topology front end overcomes the shortcoming effectively. When more and more receivers (RX) and transmitters (TX) are integrated into one chip, the linearity of the receiver front end becomes a very important performer that handles the TX and RX feedthrough. Another reason for the requirement of good linearity is the massive electromagnetic interference that exists in the atmosphere. This paper presents a linearity-improved RF front end with a feedforward body bias (FBB) subharmonic mixer core topology that satisfies modern RF front end demands. A novel complementary derivative superposition (DS) method is presented in low noise amplifier (LNA) design to cancel both the third- and second-order nonlinearities. To the best knowledge of the authors, this is the first time FBB technology is used in the SHPM core to improve linearity. A Volterra series is introduced to provide an analytical formula for the FBB of the SHPM core. The design was fabricated in a 0.13 μm complementary metal oxide semiconductor (CMOS) process with a chip area of 750 μm × 1270 μm. At a 2.4 GHz working frequency, the measurement result shows a conversion gain of 36 dB, double side band (DSB) noise figure (NF) of 6.8 dB, third-order intermodulation intercept point (IIP3) of 2 dBm, LO–RF isolation of 90 dB and 0.8 mW DC offset with 14.4 mW power consumption at 1.2 V supply voltage. These results exhibit better LO–RF feedthrough and DC offset, good gain and NF, moderate IIP3 and the highest figure of merit compared to the state-of-the-art publications.

Derivative superposition method for DG MOSFET application to RF mixer

Derivative Superposition Numerical Method for Double-Gate MOSFET Transistor Application to RF Mixer

High linearity 2<sup>nd</sup> IF CMOS mixer for DRM/DAB receiver

Linearity Improvement Using a Modified Derivative Superposition Method in Cascaded Stages Amplifier

A 24-to-30 GHz Ultra-High-Linearity Down-Conversion Mixer for 5G Applications Using a New Linearization Method

A 2.1–2.5 GHz high linearity and low noise down-conversion active mixer

The improvement of device linearity in AlGaN/GaN HEMTs at millimeter-wave frequencies using dual-gate configuration

Double-balanced Mixer Based on Monolayer Graphene Fieldeffect Transistors

Analysis and Implementation of Derivative Superposition for A Power Amplifier Driver

Arbitrary Alloy Semiconductor Material Based DG MOSFET for High-Frequency Industrial and Hybrid Consumer Applications

A High Performance Double-Balanced Gilbert Mixer with Active Loads for 2.4-GHz ISM Band Application

A Linearity Improvement Front End with Subharmonic Current Commutating Passive Mixer for 2.4 GHz Direct Conversion Receiver in 0.13 Μm CMOS Technology

Device considerations and modeling for the design of an InP-based MODFET millimeter-wave resistive mixer with superior conversion efficiency

A double-balanced down converter mixer in GaN-on-Si HEMT technology

A 39 GHz Broadband High-Isolation CMOS Mixer Using Magnetic-Coupling CG Gm Stage for 5G Applications

Operation of Mixer Comprising a Series-Connected Distributed Superconductor–Insulator–Superconductor Junction Array

A computational approach to optimize the linearity in dual-gate InAlGaN/AlN/GaN HEMTs

Double-Balanced Graphene Integrated Mixer with Outstanding Linearity.

Design of a Dual-Material Gate LDMOS

High Performance SOI Gate-Bulk Connected LCMOSFET for RF Power Amplifier Application in Short and Medium Range Wireless Communication Systems

A LOW POWER, HIGH-LINEARITY CMOS DOWNCONVERSION FOLDED MIXER FOR 2.4GHz ISM BAND APPLICATIONS