Abstract:Mesoporous carbon materials with ultra-thin carbon pore walls and highly dispersed Ni nanoparticles have been successfully prepared by using two different SBA-15 silicas as hard templates and 2,3-dihydroxynaphthalene (DHN) as a carbon precursor. The nickel precursor was a concentrated nickel nitrate hexahydrate [Ni(NO3)(2)center dot 6H(2)O] solution in 2-propanol, which was added to the carbon-silica nanocomposite prior to thermal treatment. The samples studied were analyzed by thermogravimetry (TG), nitrogen adsorption at -196 degrees C, powder X-ray diffraction (XRD), Raman spectroscopy, scanning and transmission electron microscopy (STEM), and in situ electron diffraction X-ray spectroscopy (EDX). While TG analysis revealed carbon contents lower than 30 wt.-%, nitrogen adsorption provided information about the homogeneity of the carbon thin film deposited onto the mesopore walls of the ordered silica templates SBA-15. The templates, carbon-silica nanocomposites, and carbon inverse replicas with nickel nanoparticles exhibit uniform pores, high surface areas, and large pore volumes. Partially graphitic carbon was identified by the presence of a characteristic G band in the Raman spectra, whereas the diffraction peak attributed to the stacking of graphene planes was not observed by powder XRD. The presence of ordered domains in the carbon materials studied was confirmed by small angle XRD and STEM imaging. In addition, the STEM images revealed that the nickel nanoparticles are uniform in size, ca. 3 nm, and are homogeneously dispersed on the tubular carbon walls. A few larger clusters of nickel, ca. 60 nm, present on the external surface, were identified by powder XRD as metallic Ni. The in situ EDX revealed that the small nanoparticles are largely composed of Ni with traces of NiO. Similar nanoparticle dispersions have been reported only for Ni-containing multiwalled carbon nanotubes (CNTs), whereas previously reported ordered mesoporous carbon materials, CMK-3, possess larger Ni/NiO nanoparticles. ((C) Wiley-VCH Verlag GmbH & Co. KGaA, 69451 Weinheim, Germany, 2009)

Preparation of Hollow Nickel Fibres by Electroless-Plating Technique

Preparation for the Hollow Nickel Fibres of the Positive Current Collector by Electroless Plating Technique

Preparation and Characterization of Nano-Particles Nickel Hollow Fibers

Ni Plating on Carbon Fiber on the Condition of Alkali

A Study on the Surface Oxidation Pretreatment and Nickel Plating Mechanism of Carbon Fiber

Fabrication of Al-Ni nanofibers by selective etching

Mesoporous Carbon Materials with Ultra‐Thin Pore Walls and Highly Dispersed Nickel Nanoparticles

Effect of nickel electroplating followed by a further copper electroplating on the micro-structure and mechanical properties of high modulus carbon fibers

Electrochemical study of Ni deposition on carbon microfiber

Preparation and Electrical Conductivity of Pt/NiO Nanofibers

Electroless plating of copper on carbon fiber surfaces and corresponding mechanism

Preparation and corresponding structure of nickel foam

Hollow Nickel Fibre Felt for Current Collector of Ni/MH Battery

ELECTROLESS PLATED MULTIWALLED CARBON NANOTUBES FOR REINFORCING METAL-MATRIX COMPOSITES

Preliminary Study on Electroless Nickel Plating for Surface Modification of Carbon Fiber

Study on new process of electroless copper plating pretreatment on carbon fiber surface

Preparation and characterisation of the Ni-C composite coating electrodeposited with carbon sol

Nickel Chains Assembled by Hollow Microspheres and Their Magnetic Properties

Reaction Kinetics and Mechanism of Nickel Fiber Synthesis

Preparation of nylon 6/PLA blend nanofibers by needleless electrospinning

Electrochemical co-deposition of carbon nanotube/Ni composite layer