Abstract:The use of carbon nanotubes (CNTs) as the reinforcing phase to prepare copper-based composite materials can improve the strength and high conductivity of copper-based conductors. In order to analyze the effect of surface oxidation modification on the structural properties of carbon nanotubes and its strengthening effect on composite materials, this article combines heterogeneous copolymerization liquid phase mixing method and spark plasma sintering molding method; prepares the carbon nanotubes/copper composite materials using carbon nanotubes under different oxidation treatment conditions as the reinforcing phase (the volume fraction of carbon nanotubes is 3%); and characterizes the microstructure, mechanical properties, and electrical and thermal conductivity of the composite material. Studies have shown that the tensile strength and hardness of composite materials first increase with the increase of CNT oxidation treatment time and then decrease with the increase of oxidation treatment time. When the oxidation treatment time is 4 h, CNTs are uniformly dispersed in the matrix while maintaining good structural integrity and load-bearing capacity, and the composite material has the highest mechanical properties. The tensile strength of the composite material made of 80‐ nm CNTs reaches 452.4 MPa, which is 1.6 times that of pure copper, and the hardness reaches 127.4HV, which is twice that of pure copper. The electrical conductivity and thermal conductivity of the composite material first increase with the increase of the oxidation treatment time of carbon nanotubes and then decrease with the increase of the oxidation treatment time. The 80 nm CNT reinforced composite material has better CNT dispersion performance and higher conductivity than that of 15 nm CNT preparation. The electrical conductivity of the composite material reaches the maximum value of 92% IACS when the CNT oxidation treatment time is 4 hours, which is 95% of the pure copper sample, and the electrical conductivity is significantly better than that of the CNT/Cu composite material and copper alloy prepared by other methods. The thermal conductivity of composite materials is lower than that of pure copper. The thermal conductivity of carbon nanotubes with an oxidation treatment time of 2 h decreases most obviously, indicating that the thermal resistance generated by the interface and agglomeration phases in the composite material affects its thermal conductivity.

Effect of nickel electroplating followed by a further copper electroplating on the micro-structure and mechanical properties of high modulus carbon fibers

Enhanced Interfacial Properties of High-Modulus Carbon Fiber Composites Via Molecular Assembly on Fiber Surface

A Study on the Surface Oxidation Pretreatment and Nickel Plating Mechanism of Carbon Fiber

Influence of carbon fibers on interfacial bonding properties of copper-coated carbon fibers

Growth mechanism and thermal behavior of electroless Cu plating on short carbon fibers

Improvement in Structural and Magnetic Properties of Electrospun Ni&lt;sub&gt;1-x&lt;/sub&gt;Cu&lt;sub&gt;x&lt;/sub&gt;Fe&lt;sub&gt;2&lt;/sub&gt;O&lt;sub&gt;4&lt;/sub&gt; Nanofibers

Electroless plating of copper on carbon fiber surfaces and corresponding mechanism

ELECTROLESS PLATED MULTIWALLED CARBON NANOTUBES FOR REINFORCING METAL-MATRIX COMPOSITES

Ni Plating on Carbon Fiber on the Condition of Alkali

Effect of technological parameters on the process of copper deposition on chemically and chemical-galvanically nickel-plated fibers

Investigation of the mechanical behavior of the carbon nanotubes coated copper composite materials

Effect of surface modification on interfacial microstructures and mechanical properties of continuous CF/Al composites

Preliminary Study on Electroless Nickel Plating for Surface Modification of Carbon Fiber

Study on new process of electroless copper plating pretreatment on carbon fiber surface

Effect of Surface Modification of Carbon Nanotubes on the Properties of High-Strength and High-Conductivity Copper Matrix Composites

Copper and Nickel Coating of Carbon Fiber for Thermally and Electrically Conductive Fiber Reinforced Composites

Interfacial Bonding Improvement through Nickel Decoration on Carbon Nanotubes in Carbon Nanotubes/Cu Composite Foams Reinforced Copper Matrix Composites

Investigation of the Mechanical Properties of the Ni–P–CNTs Coated Copper Composite Materials: Experiments and Modeling

Effect of Cu/Ni coating on the interface and mechanical properties of C f /2024Al composites

Preparation of Hollow Nickel Fibres by Electroless-Plating Technique

Effects of the addition of Ni-plated carbon nanotube on the microstructure and properties of injection molded FeAl