Abstract:Wake-up receivers (WuRXs) help to significantly reduce the average power of the Internet of the Things (loT) hardware systems. To lower the “asleep” power in the idle state, the WuRX structures based on non-standard protocols have been widely studied in prior researches, which can realize a high sensitivity [1] or low power [2]. Compared to the non-standard receivers, there are more design challenges in the standard-compliant WuRXs. For example, a BLE-compliant WuRX operating in the congested 2.4GHz band should be able to handle potentially large interferers including adjacent-channel tone and image, as well as realize a high sensitivity for long-reach access. Therefore, there have been several conventional solutions for the interference-resilient BLE-compliant WuRXs: 1) Single-path down-conversion WuRXs. The interference is handled by an RF filter [3] or a low-noise LO [4] (Fig. 1, top). The WuRX in [3] utilized an FBAR filter to reject the interference from the adjacent channel, resulting in a signal-to-interference ratio (SIR) of −6dB@2MHz, where the loss of FBAR filter degraded the sensitivity to −85dBm. An LC oscillator based LO was adopted in [4] to suppress the adjacent-channel interference by −10dB, but it's at the penalty of 1.2mW power. 2) I/Q-path down-conversion WuRXs. A Hartley WuRX was designed in [5] to reject both 2MHz adjacent-channel interference and image (Fig. 1, middle), as well as improve the sensitivity to −92dBm, while the I/Q downconverters and LO generators dominated the total power consumption. Although the WuRX power was reduced to 352μW by the edge combiner based I/O LO generation, the SIR was limited to −12.5dB due to the spurs and noise accompanying the LO signal. As a result, it's difficult for the conventional WuRX structures to realize both a high SIR and low power consumption.

A Passive RF Receiving and Power Switch ASIC for Remote Power Control with Zero Stand-by Power

A RF remote-control transceiver with zero-standby power based on RFID technology

Design ＆ Implementation of an Energy Saver IC for AC Contactor

A CMOS Low Power K-band FMCW Radar Transceiver Front-End for AIOT Application

Wireless Switch for Implantable Medical Devices Based on Passive RF Receiver

Remote Control System for Battery-Assisted Devices with 16 nW Standby Consumption

An Energy-Efficient ASIC with Real-Time Work-on-demand for Wireless Body Sensor Network

An Energy-Efficient ASIC for Wireless Body Sensor Networks in Medical Applications

A Low Power Pulse Signal Acquisition ASIC for MEMS Switch

A Switch Type RF Energy Harvesting and Management System

A generic miniature multi-feature programmable wireless powering headstage ASIC for implantable biomedical systems

A Novel Soft-Switching Dual-Side Phase Shift Circuit for Wireless Power Transfer

A Zero Static Power Consumption Bi-Stable RF MEMS Switch Based on Inertial Generated Timing Sequence Method

A Wireless Capsule Endoscope System with Low-Power Controlling and Processing ASIC

An Interference-Resilient 120-Degree-apart Pseudo-I/Q BLE-Compliant Wake-Up Receiver Achieving-21dB SIR,-94dBm Sensitivity, and 4-D Wake-Up Signature

A Low-Power RF Front-End of Passive UHF RFID Transponders

A low-power AC/DC rectifier for passive UHF RFID transponders

A 0.66mw 400 MHz/900 MHz Transmitter IC for In-Body Bio-Sensing Applications.

A Sub-GHz Low-Power Transceiver with PAPR-tolerant Power Amplifier for 802.11ah Applications

A low power and high performance analog front end for passive RFID transponder

A 2.4 GHz 2.9 Mw Zigbee RF Receiver with Current-Reusing and Function-Reused Mixing Techniques