Abstract:Reactive melt infiltration (RMI) has been proved to be one of the most promising technologies for fabrication of C/SiC composites because of its low cost and short processing cycle. However, the poor mechanical and anti-ablation properties of the RMI-C/SiC composites severely limit their practical use due to an imperfect siliconization of carbon matrixes with thick walls and micron-sized pores. Here, we report a high-performance RMI-C/SiC composite fabricated using a carbon fiber reinforced nanoporous carbon (NC) matrix preform composed of overlapping nanoparticles and abundant nanopores. For comparison, the C/C performs with conventional pyrocarbon (PyC) or resin carbon (ReC) matrixes were also used to explore the effect of carbon matrix on the composition and property of the obtained C/SiC composites. The C/SiC derived from C/NC with a high density of 2.50 g cm -3 has dense and pure SiC matrix and intact carbon fibers due to the complete ceramization of original carbon matrix and the almost full consumption of inspersed silicon. In contrast, the counterparts based on C/PyC or C/ReC with a low density have a little SiC, much residual silicon and carbon, and many corroded fibers. As a result, the C/SiC from C/NC shows the highest flexural strength of 218.1 MPa and the lowest ablation rate of 0.168 μm s -1 in an oxyacetylene flame of ~ 2200 °C with a duration time of 500 s. This work opens up a new way for the development of high-performance ceramic matrix composites by siliconizing the C/C preforms with nanoporous carbon matrix

Fabrication and mechanical properties of SiCf/SiC composites via polycarbosllane pyrolysis

Mechanical Behavior of SiCf/SiC Composites with Alternating PyC/SiC Multilayer Interphases

Mechanical Properties of 3D KD-I SiCf/SiC Composites with Engineered Fibre–matrix Interfaces

Influence of SiC Coating Thickness on Mechanical Properties of SiCf/SiC Composite

Influence of polycarbosilane composition on the properties of SiC/SiC composite fabricated by precursor infiltration and pyrolysis process

Mechanical Properties and Failure Behavior of 3D-SiCf/SiC Composites with Different Interphases

Fabrication of C/SiC composites by siliconizing carbon fiber reinforced nanoporous carbon matrix preforms and their properties

Microstructure and mechanical properties of SiC f /SiC composite prepared by chemical vapor infiltration

Structure and properties of fine diameter continuous SiC ceramic fiber reinforced Al matrix composites

Fabrication of dense Cf/SiC ceramic matrix composites using 3D printing and PIP with short carbon fibre as a toughening material

Preceramic Paper-Derived SiCf/SiCp Composites Obtained by Spark Plasma Sintering: Processing, Microstructure and Mechanical Properties

Fabrication and Mechanical Properties of SiCw(p)/SiC-Si Composites by Liquid Si Infiltration using Pyrolysed Rice Husks and SiC Powders as Precursors

Mechanical properties and strengthening mechanism of SiCf/SiC mini-composites modified by SiC nanowires

Preparation and mechanical behaviors of multiscale SiC nanowires/carbon fiber reinforced silicon oxycarbide ceramic composites

Influence of pyrolytic carbon interphase and pyrolysis temperature on the mechanical and tribological properties of Cf/SiC after heat treatment at 1800 °C

Preparation and Properties of Porous SiC/SiC Composites

Fabrication, microstructure, and properties of SiC/Al4SiC4 multiphase ceramics via an in-situ formed liquid phase sintering

Microstructure and mechanical properties of 3D Cf/SiBCN composites fabricated by polymer infiltration and pyrolysis

Microstructural investigations of the pyrocarbon interphase in SiC fiber-reinforced SiC matrix composites

Microstructure and mechanical properties of quasi-isotropic chopped fiber-reinforced PyC–SiC matrix composite prepared by novel nondamaging method

Fabrication and characterization of pyrolytic carbons from phenolic resin reinforced by SiC nanowires with chain-bead structures