Abstract:This study addresses the challenge of achieving foam with a high expansion ratio and poor mechanical properties, caused by the low melt viscosity of semi-crystalline polypropylene (PP). We systematically employ a modification approach involving blending PP with polyolefin elastomers (POE), irradiation crosslinking, and fiber reinforcement to prepare fiber-reinforced crosslinked PP/POE composite foam. Through optimization and characterization of material composition and processing conditions, the obtained fiber-reinforced crosslinked PP/POE composite foam exhibits both low density and high performance. Specifically, at a crosslinking degree of 12%, the expansion ratio reaches 16 times its original value, and a foam density of 0.057 g/cm3 is reduced by 36% compared to the non-crosslinked PP/POE system with a density of 0.089 g/cm3. The density of the short-carbon-fiber-reinforced crosslinked sCF/PP/POE composite foam is comparable to that of the crosslinked PP/POE system, but the tensile strength reaches 0.69 MPa, representing a 200% increase over the crosslinked PP/POE system and a 41% increase over the non-crosslinked PP/POE system. Simultaneously, it exhibits excellent impact strength, tear resistance, and low heat shrinkage. Irradiation crosslinking is beneficial for enhancing the melt strength and resistance to high temperature thermal shrinkage of PP/POE foam, while fiber reinforcement contributes significantly to improving mechanical properties. These achieve a good complementary effect in low-density and high-performance PP foam modification.

Study on Structure and Properties of PP/POE Blends with Ultrasonic Irradiation During Extrusion

Effect Of Polyethersulfone On The Mechanical And Rheological Properties Of Polyetherimide-Modified Epoxy Systems

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Comparative Study of Paired Serum and Cerebrospinal Fluid Samples from Neurocysticercosis Patients for the Detection of Specific Antibody to Taenia solium Immunodiagnostic Antigen

Effect of Morphology Development on the Low‐temperature Tensile Properties of PP / POE Blends

Realizing Simultaneous High‐temperature Strength and Low‐temperature Elongation in Polyolefin Elastomer Toughened Polypropylene Via Controlling the Dispersed Phase Size

Morphology, thermal behavior, rheological, and mechanical properties of polypropylene/polystyrene blends based on elongation flow

The study of the chemical crosslinked and foamed PP/LDPE

Study on Structure and Properties of HDPE Functionalized by Ultraviolet Irradiation in Air and O2 Atmosphere

Interstate dispensing: a case for uniform, intuitive legislation.

Understanding the effect of silane crosslinking reaction on the properties of PP/POE blends

ULTRAVIOLET IRRADIATION MODIFICATION OF HDPE AND MECHANICAL PROPERTIES OF ITS BLEND WITH PVA

Enhanced compatibility of PA6/POE blends by POE-g-MAH prepared through ultrasound-assisted extrusion

Low-Density and High-Performance Fiber-Reinforced PP/POE Composite Foam via Irradiation Crosslinking

A study on ultraviolet irradiation modification of high-density polyethylene and its effect in the compatibility of HDPE/PVA fibre composites

Effect of gamma irradiation on ethylene–octene copolymers

Studies on Linear Low-Density Polyethylene Functionalized by Ultraviolet Irradiation and Its Compatibilization

A Study of Ultraviolet Irradiation Functionalization of LLDPE and Its Modification of PA66

Investigation of Crystallization, Morphology, and Mechanical Properties of Polypropylene/Polypropylene-Polyethylene Block Copolymer Blends

Studies On High Density Polyethylene (Hdpe) Functionalized By Ultraviolet Irradiation And Its Application

Toughening and reinforcing waste polypropylene with POE / nano‐SiO 2 under elongational flow