Abstract:<p>High borated steel sheets containing 0.25 wt% to 4.0 wt% boron including hypoeutectic (0.28 wt% B and 2.11 wt% B), eutectic (2.43 wt% B) and hypereutectic (4.01 wt% B) compositions were tried to be fabricated by a novel strip casting technology, and the effects of boron content on sub-rapid solidification behavior and subsequent microstructural evolution together with mechanical properties was studied. It was found that the morphology of borides depended greatly on the boron content. When increasing boron, the morphological change of borides was network-like → grainy → cluster-like → plate-like. Various orientation relationships between different morphological borides and γ-Fe in as-cast steels were also identified. After subsequent hot-rolling and solution-treating, ultra-fine (<10 μm) borides were obtained in hypoeutectic and eutectic steels. Benefiting from that, excellent mechanical properties was achieved, which was much better than that of steels prepared by traditional ingot casting. Particularly, when the boron content approached eutectic composition, of which the effect on the microstructure and mechanical properties was more sensitive. The steels containing 2.11 wt% and 2.43 wt% boron exhibited different morphological borides with a total elongation of 14.1% and 8.0%, respectively. Moreover, a thin hypereutectic borated steel sheet was also prepared, but the borides were very large and the total elongation was very low. The correlation between microstructure and strength was clarified based on the Hall-Petch behavior and intermetallic strengthening effect. Smaller γ-grains and higher volume fraction of borides were responsible for higher strength. The plastic behavior of steels was influenced by strain-hardening rate that was determined by the volume fraction of γ-Fe matrix. A better sustainable strain-hardening capability was beneficial to extend the stage of uniform deformation and enhance the ductility. In addition, the mechanical properties of steels were also decided by the fracture mechanism that was dominated by the size of borides.</p>

Effect of RE-Mg on High Boron Iron-Base Alloy

High Boron Iron-Based Alloy and Its Modification

Morphology Improvement of Boride in High Boron Wear Resistance Alloy

The Effects of RE-Mg on Thermal Fatigue Resistance of Cast High Speed Steel (HSS) Rolls

Effect of rare earth elements on microstructure and mechanical properties of bainite/martensite bearing steel

Effect of boron on microstructure evolution and properties of wear-resistant cast Fe–Si–Mn–Cr–B alloy

Effect of Boron and Carbon Content on Microstructure and Properties of High Boron Iron-Based Alloy

Effect of Trace Boron Addition on the Microstructural Evolution and Mechanical Properties in Ti45al8nb2cr-B Alloys

The Microstructural Evolution and Mechanical Properties of Boron-Doped Ti35Zr30V10Nb25 Refractory High-Entropy Alloy

Effect of Re addition on the microstructure and mechanical properties of AlCoCrFeNi 2.1 eutectic high-entropy alloy

Boron microalloying for high-temperature eutectic high-entropy alloys

The Effect of Mixed RE Elements on Microstructure and Mechanical Properties of Die-Cast AZ91D Alloy

Effects of rhenium and high-angle grain boundaries upon the elemental distribution and microstructure of Ni-based single-crystal superalloys

Significant Improvement in Wear Resistance of CoCrFeNi High-Entropy Alloy via Boron Doping

Effect of Double Plastic Deformation on Microstructure and Mechanical Properties of High-Content Rare-Earth AZ61 Mg Alloy

Effect of Boronizing on the Microstructure and Mechanical Properties of CoCrFeNiMn High-Entropy Alloy

Influence of rare earth addition on microstructures and mechanical properties of high-pressure die casting Mg–8Zn–6Al alloy

Effect of rare earth (RE) on pack boronising process of titanium alloy

Effects of boron content on the microstructure and mechanical properties of twin-roll strip casting borated steel sheets

Influence of Re-Ti Modification on the High Impact Wear Resistance of High Si Bainitic Cast Steel

Influence of minor RE addition on microstructures, tensile properties, and creep resistance in a die-cast Mg–Al–Ca–Mn alloy