Abstract:The microstructure and mechanical characteristics of the AZ61 magnesium alloy with varying RE (RE) content during the extrusion-forging process were thoroughly examined using metallography, SEM, EDS, and XRD. Findings indicate that as the RE content increases, the β-Mg 17 Al 12 phase is significantly diminished, primarily resulting in a microstructure composed of Al 4 Ce and Al 8 Mn 4 Ce phases or Al 3 Nd and Al 4 Ce phases, along with a minor presence of Al 4 La phase, which appears in black granular or agglomerated forms along the extrusion axis. Following die forging, the RE phases in the AZ61+xRE Mg alloy's microstructure experienced secondary fragmentation due to triaxial compressive stress, leading to a drum-shaped or S-shaped distribution of the fractured RE material, without any spheroidization or new phase formation occurring during deformation, while the β-Mg 17 Al 12 phase was entirely dissolved in the matrix. Post die forging, the mechanical properties of the AZ61+xRE magnesium alloy showed significant enhancement, with the AEZ641 alloy exhibiting the highest increases in tensile strength and yield strength, at 8.5 and 26.2%, respectively. Nonetheless, the elongation of all four alloys decreased markedly, by 42 to 52%, and hardness increased by 3.5 to 7.1%. As RE content rose, the yield strength, tensile strength, elongation, and hardness of the as-forged AEZ611 alloy reached values of 220 MPa, 302.3 MPa, 11.25%, and 65.8 HRE, respectively, showcasing the best overall mechanical properties at room temperature. During the transition from extrusion to die forging, the macrofracture exhibited distinct necking, while the microfracture revealed numerous pits, with a significant presence of second phase or RE particles located at the pits' bottoms. The fracture mechanism was identified as a mixed fracture with characteristics of toughness.

Influence of rare earth addition on microstructures and mechanical properties of high-pressure die casting Mg–8Zn–6Al alloy

Effects of RE on the Microstructure and Mechanical Properties of Mg–8Zn–4Al Magnesium Alloy

Effects of chemical composition on the microstructure and mechanical properties of gravity cast Mg-xZn-yRE-Zr alloy

Microstructure and Mechanical Properties of Mg-3Al-1Zn-xRE Alloys

Influence of minor RE addition on microstructures, tensile properties, and creep resistance in a die-cast Mg–Al–Ca–Mn alloy

Mechanism of high-strength and ductility of Mg-RE alloy fabricated by low-temperature extrusion and aging treatment

Effects of Re on Microstructure and Properties of Az91 Magnesium Alloy

Microstructure and Mechanical Properties of a Novel Mg–RE–Zn–Y Alloy Fabricated by Rheo-Squeeze Casting

Effects of Rare Earths on the Microstructure, Properties and Fracture Behavior of Mg–Al Alloys

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

Effects of RE on Microstructures of Mg-8Zn-4Al-0.3Mn Magnesium Alloys

Fast shot speed induced microstructure and mechanical property evolution of high pressure die casting Mg-Al-Zn-RE alloys

Revealing precipitation behavior and mechanical response of wire-arc directed energy deposited Mg-Gd-Y-Zr alloy by tailoring aging procedures

Influence of Heat Treatment on Microstructures and Mechanical Properties of Gravity Cast Mg–4.2Zn–1.5RE–0.7Zr Magnesium Alloy

Effects of Zn and RE Additions on the Solidification Behavior of Mg–9Al Magnesium Alloy

Effect of Double Plastic Deformation on Microstructure and Mechanical Properties of High-Content Rare-Earth AZ61 Mg Alloy

Synergistic Effects of Cerium-Based Rare Earth Addition and Hot Deformation on the Microstructure and Mechanical Properties of Mg-0.5Zn-0.5Zr Magnesium Alloy

The Effect of Mixed RE Elements on Microstructure and Mechanical Properties of Die-Cast AZ91D Alloy

Development and characteristics of a low rare-earth containing magnesium alloy with high strength-ductility synergy

Development of high mechanical properties and moderate thermal conductivity cast Mg alloy with multiple RE via heat treatment

Effects of addition of Er and Zr on microstructure and mechanical properties of Al–Cu–Mn–Si–Mg alloy