Abstract:In some circumstances, hybrid polymer microfluidic chips composed of both elastic, gas-permeable polydimethylsiloxane (PDMS) and rigid plastics are needed. However, it is quite difficult to bond PDMS irreversibly to plastics such as polystyrene (PS). In this article, a facile method for irreversible bonding of PDMS to PS was proposed based on UV/O-3-assisted surface modification in combination of surface silanization. Firstly, a PS sheet was exposed to UV/O-3 to produce oxygen-containing polar moieties, such as hydroxyl and carboxylic acid, on its surface. Secondly, the UV/O-3 treated PS sheet was silanized with (3-aminopropyl)triethoxysilane (APTES) via the reaction between the oxygen-containing polar moieties on the PS surface and the molecules of APTES. Thirdly, the silanized-PS sheet and the PDMS substrate with micro channel network were treated with UV/O-3 again to generate silanol moieties on both surfaces. Finally, the UV/O-3 treated PDMS was immediately brought intimate contact with the UV/O-3 treated silanized-PS, and irreversible bonding of PDMS with PS occurred after putting the PDMS-PS complex at room temperature for 1 h through the condensation reaction between silanol moieties. Contact angle measurement, X-ray photoelectron spectroscopy, total reflection Fourier transformation infrared spectrometer were applied to characterize the surface chemistry of the PS during the UV/O-3 treatment and silanization. The hybrid PDMS-PS microfludic chips prepared with the established method can bear a gas pressure higher than 0.5 MPa and a water stream at a flow rate higher than 170 mu L/min (the test channels were 2.5 cm in the length, 50 mu m in the width, 200 mu m in the depth). A hybrid PDMS-PS microfluidic chip composed of gas-permeable PDMS substrate with channel network and excellently biocompatible PS cover sheet was fabricated for cell culture. The experimental results showed that HeLa cells cultured in the hybrid PDMS-PS microchip grew much better than those cultured in the full PS microchip, and slightly better than those in the full PDMS microchip.

Plastic-Silicon Bonding for MEMS Packaging Application

A strategy of wafer-level-plastic-packaging for MEMS based on adhesive bonding

Bonding of Aluminum Coated Silicon Wafers Based on Polypropylene Carbonate and As a Multi-Functional Sensor

Novel Bonding technologies for wafer-level transparent packaging of MOEMS

Removable Fast Packing Of Mems Devices Using Polymer Connectors And Silicon Sockets

Removable Fast Package Technology For Mems Devices Using Polymer Connectors And Silicon Sockets

Chip Level Packaging for Mems Using Silicon Cap

Design and Fabrication of High Performance Wafer-Level Vacuum Packaging Based on Glass–silicon–glass Bonding Techniques

PMMA Solution Assisted Room Temperature Bonding for PMMA–PC Hybrid Devices

Progress in wafer bonding technology towards MEMS, high-power electronics, optoelectronics, and optofluidics

MEMS vacuum packaging technology and applications

Fabrication of Fluidic Chips with 1-D Nanochannels on PMMA Substrates by Photoresist-Free UV-lithography and UV-assisted Low-Temperature Bonding

An Approach for Irreversible Bonding of PDMS-PS Hybrid Microfluidic Chips at Room Temperature

Fabrication of a Three-Dimensional Microfluidic System from Poly(methyl methacrylate) (PMMA) Using an Intermiscibility Vacuum Bonding Technique

Fabrication of Micro Pneumatic Valves with Double-Layer Elastic Poly(dimethylsiloxane) Membranes in Rigid Poly(methyl Methacrylate) Microfluidic Chips

Investigation of Au/Si Eutectic Wafer Bonding for MEMS Accelerometers

Hermetic Packaging of Mems with Thick Electrodes by Silicon-Glass Anodic Bonding.

Electrostatic Bonding of A Silicon Master to A Glass Wafer for Plastic Microchannel Fabrication

A simple and low-cost approach for irreversible bonding of polymethylmethacrylate and polydimethylsiloxane at room temperature for high-pressure hybrid microfluidics

Mechanism and Process of Cu-Sn Bonding for Wafer Level MEMS Packaging

Bonding Packaging Of A Sp4t Rf Mems Switch