A C+L-band Erbium-Doped Fiber ASE Source Using Dual-Forward Pumping Configuration

Wencai Huang,Chaohong Huang,Xiulin Wang,Benrui Zheng,Huiying Xu,Zhiping Cai

DOI: https://doi.org/10.1109/aoe.2007.4410818

2007-01-01

Abstract:We present a C+L-band ASE fiber source using double-pass dual-forward pumping configuration. The proposed ASE source offers a high pumping efficiency of 24.6%, output power of 52mW and a wide bandwidth of about 80nm.

What problem does this paper attempt to address?

Low-Ripple and High-Efficiency C+L-Band Erbium-Doped Fiber Amplified-Spontaneous-Emission Sources Using A Dual Forward Pumping Configuration

Wencai Huang,Benrui Zheng,Xiulin Wang,Minghao Sun,Huiying Xu,Zhiping Cai

DOI: https://doi.org/10.1117/1.2890470

IF: 1.3

2008-01-01

Optical Engineering

Abstract:We have experimentally investigated a new two-stage C+L-band (1525 to 1605-nm) amplified spontaneous emission (ASE) fiber source using a dual forward pumping configuration. The proposed source offers a high pumping efficiency of 24.6%, output power of about 52 mW, and a wide bandwidth of 80 nm. Without using any external spectral filters, the source has a low spectral ripple between 2.4 and 2.9 dB for different pumping power levels. This designed configuration is also suitable for high-efficiency L-band ASE. The obtained source will be useful in characteristic measurement for wavelength-division multiplexing components and spectrum-sliced multiwavelength fiber sources for local access networks.
A Double-pass Erbium-doped Fiber Based Broadband ASESource by Utilizing C-band ASE Compensation

Zhang Hao,Yuan Shuzhong,Yu Ling,Liu Yange,Xiong Lingyun,Li Yao,Dou Qingying,Liu Lihui,Dong Xiaoyi

DOI: https://doi.org/10.3969/j.issn.0465-7942.2006.05.003

2006-01-01

Abstract:A two-stage broadband erbium-doped fiber based amplified spontaneous emission(ASE) source is presented.By using double-pass configuration and recycling backward C-band ASE,the pump power for(L-band) ASE generation is much economized.With a chirped fiber Bragg grating(CFBG) as spectrum equalizer,a flat spectral bandwidth of 76 nm is realized.
Theoretical and Experimental Analysis of Bidirectionally Pumped 1.3 Μm Pr3+-doped ASE Source

Jiapeng Mou,Tengchao Huang,Shuangliang Che,Xiaowu Shu

DOI: https://doi.org/10.1007/s11082-019-1895-8

IF: 3

2019-01-01

Optical and Quantum Electronics

Abstract:We have analyzed the characteristics of 1.3 μm praseodymium (Pr3+) doped bidirectionally pumped double pass (BIP-DP) configuration amplified spontaneous emission (ASE) source theoretically and experimentally. The source’s simulation model was established and corresponding simulated results were given. The effects of pump ratio, Pr3+-doped fiber (PDF) length, total pump power and source’s optical losses were researched. The output power of BIP-DP ASE source is mainly affected by the total pump power, PDF length and source’s optical losses, while it has little relationship with the pump ratio. The BIP-DP ASE source operating at the symmetric bi-directional pump condition was constructed experimentally. The acquired output power of more than 5 mW has been obtained experimentally, which was with the quasi-gaussian output spectrum, and its 3 dB bandwidth is ~ 20 nm.
C+L-Band Erbium-Doped Fiber Broadband Light Source Using One-Stage Configuration

WANG Xiu-lin,MING Hai,WANG An-ting,HUANG Xiao-jing,HUANG Wen-cai

DOI: https://doi.org/10.3321/j.issn:0258-7025.2006.02.006

2006-01-01

Chinese Journal of Lasers

Abstract:A high efficiency amplified spontaneous emission(ASE) broadband fiber source by using the bi-directional pumped one-stage configuration is reported.The experimental results show that a C+L-band flat-spectrum fiber source with bandwidth of 80 nm(1525～1605 nm) was obtained by adjusting the forward and backward pump power within a certain fiber length.The pump conversion efficiency is relevant to the erbium-doped fiber (EDF) length and the pump power allotment of forward and backward pump lasers.Selecting the required shortest fiber length has the benefit of improving pump conversion efficiency as well as cutting down the cost for reasons of shorter erbium-doped fiber needed.A high efficiency C+L-band ASE source with the output power of 13.5 dBm and pump conversion efficiency of 23.2% is obtained experimentally using this configuration.
Simulation Analysis of One-Stage C+L-band Erbium-Doped Fiber ASE Source with Double-Pass Bi-Directional Pumping Configuration

Wencai Huang,Hai Ming

IF: 2.56

2004-01-01

Chinese Optics Letters

Abstract:A new technique to generate a C+L-band flat amplified spontaneous emission (ASE) source in one-stage erbium-doped fiber (EDF) using bi-directional pumping configuration is analyzed. The simulation results show that the key point of obtaining flat C+L-band ASE spectrum in one-stage EDF is using a laser diode operated at 980nm as backward pump source. ASE source with nearly 80-nm bandwidth can be obtained by means of selecting suitable fiber length and properly adjusting the ratio of forward to backward pump power.
A Novel Two-Stage Erbium Amplified Spontaneous Emission Fiber Source with 80nm Bandwidth

XL Wang,H Ming,WC Huang

DOI: https://doi.org/10.1117/12.634305

2005-01-01

Abstract:In this paper, a practical two-stage scheme is suggested for generating a C+L-band erbium-doped fiber amplified spontaneous emission (ASE) broadband light source. A considerable power increase of the L-band ASE spectrum is achieved by injecting the C-band ASE into the long section erbium-doped fiber. The C+L-band ASE source is obtained by combining the enhanced L-band ASE with the C-band ASE from two stages respectively. A spectrum flat ASE source with nearly 80nm bandwidth and about 15.9dBm output power is obtained with a total pump power of 180mW. Namely, the pump conversion efficiency is about 21.6%. Such a broadband incoherent light source is desirable for various applications in some areas like sliced wavelength-division multiplexed local-access networks, characteristic measurement for dense wavelength-division multiplexed components, and fiber-optic sensor systems etc.
Characteristics of the dual-forward pumped L-band ASE fiber source

Xiulin Wang,Wencai Huang,Chaohong Huang,Benrui Zheng,MingHao Sun,Huiying Xu,Zhiping Cai

DOI: https://doi.org/10.1117/12.755409

2008-01-01

Abstract:We present a two-stage dual-forward pumped configuration to achieve a wavelength stable L-band amplified spontaneous emission (ASE) source. The effects of EDF length and pump power arrangements on the characteristics of L-band ASE spectrum, output power, and mean wavelength are investigated. The results show that not only the pumping conversion efficiency can be improved largely but also the pump power independent mean wavelength operation can be achieved by optimizing the fiber length ratio and pump ratio of the dual-forward pumped configuration as comparing to that of the conventional double-pass forward configuration.
Design and Optimization of a High-Power L-band ASE Fiber Source

Xiulin Wang,Chaohong Huang,Wencai Huang,Huiying Xu,Zhiping Cai,Chenchun Ye

DOI: https://doi.org/10.1117/12.725741

2007-01-01

Abstract:Two kinds of configurations of L-band amplified spontaneous emission (ASE) source with two-stage EDF and dual forward pumps are suggested for generating a high power L-band ASE spectrum. The characteristics are theoretically compared in terms of the output power, pumping conversion efficiency, bandwidth, and mean wavelength stability for these two configurations. The EDF length and pump power allotment are also optimized. An L-band ASE source of 76mW output power with about 36.2% pumping conversion efficiency are experimentally obtained.
A Selective C and L-Band Amplified Spontaneous Emission Source Using a 1×2 Optical Switch

WC Huang,H Ming,ZP Cai,HY Xu,CC Ye

DOI: https://doi.org/10.1088/0256-307x/22/4/030

2005-01-01

Chinese Physics Letters

Abstract:We report on a band selective amplified spontaneous emission (ASE) source of an erbium-doped fibre (EDF), which can operate in either the C- or L-band region. The band selective ASE source is realized using a pump conversion technique by a 1×2 optical switch, which makes the ASE source design convert between a backward and a forward pumped configuration alternately. A heavily doped erbium fibre and a 1480 nm laser diode are adopted for this design synchronously to enhance the power of L-band ASE. A power of 16.2 mW for C-band ASE and 11.8 mW for L-band ASE are obtained with a total pump power of 100 mW.
Characteristics Comparison of Optimal L-Band Er-Doped Ase Sources in Different Configurations

HY Xu,WC Huang,ZP Cai,CC Ye

DOI: https://doi.org/10.1117/12.636154

2005-01-01

Abstract:In this paper, we investigate the 1480nm pumped L-band erbium doped fiber amplified spontaneous emission source of three major configurations: one-stage double-pass forward pump configuration, two-stage with C-band ASE injection configuration, one-stage double-pass bi-directional pump configuration. The characteristics are compared in terms of the output power, pumping conversion efficiency, bandwidth, and mean wavelength stability. It is shown that the one-stage double-pass bi-directional pump configuration has a better performance than the other two configurations.
Band Selective ASE Source for Dual-Band DWDM Device Characterization and Metro Networks

XL Wang,H Ming,WC Huang

DOI: https://doi.org/10.1117/12.634199

2005-01-01

Abstract:In this paper, a novel scheme for band selection in an amplified spontaneous emission source (ASE) based on erbium-doped fiber is demonstrated. C-band operation is obtained without backward ASE feedback whereas L-band operation is obtained with backward ASE feedback with the used of a 1X2 optical switch. A selective ASE source with an output power of 27.6mW for the C-band and 11.8mW for the L-band is obtained experimentally with a total pump power of 100mW of 1480nm laser diode. This band selective ASE source convenience the users select the necessary band when needed without any form of upgrading or additional module attachment therefore has the potential use for the dual-band DWDM device characterization and metro networks.
A C-or C+L-Band Selectable ASE Source Using the Backward Feedback Technique with an Optical Switch

王秀琳 Wang Xiulin,黄文财 Huang Wencai,蔡志平 Cai Zhiping

DOI: https://doi.org/10.3788/LOP49.120601

2012-01-01

Laser & Optoelectronics Progress

Abstract:A band selectable amplified spontaneous emission(ASE) source of an erbium-doped fiber(EDF) which can operate in either the C-or the C+L-band region is proposed and demonstrated.The band selectable ASE source is realized using the backward feedback technique with a 1×2 optical switch in a bi-directional pumping configuration.The 25.9 mW C-band and 22.5 mW C+L-band ASE spectra are alternately obtained merely by controlling the state of the optical switch.
Resonantly Pumped High Power Flat L-band Erbium-Doped Superfluorescent Fiber Source

Sheng-Ping Chen,Ze-Jin Liu,Yi-Gang Li,Ke-Cheng Lu,Shou-Huan Zhou

DOI: https://doi.org/10.1364/oe.16.000207

IF: 3.8

2008-01-01

Optics Express

Abstract:An all-single-mode-fiber L-band superfluorescent fiber source (SFS) with 1 W output power, 34.3 nm bandwidth (FWHM) and 54% optical conversion efficiency is constructed by seeding a high power erbium-doped fiber amplifier (EDFA) with a low power L-band ASE seed source to avoid parasitic lasing. The source is resonantly pumped by a high power C-band SFS peaked at 1545 nm.
A Novel Conventional/Long-Band Erbium-Doped Fibre Amplified Spontaneous Emission Source With 80 Nm Bandwidth

Wc Huang,Hy Tam,Pka Wai,Xy Dong,H Ming,Jp Xie

DOI: https://doi.org/10.1088/0256-307X/19/9/328

2002-01-01

Chinese Physics Letters

Abstract:We report on a one-stage erbium-doped fibre amplified spontaneous emission (ASE) source with 80 nm bandwidth and 13.5 dBm output power. The broad bandwidth erbium ASE source was realized in an erbium-doped fibre with 37 m length by a 1480 nm laser diode and a 980 nm laser diode as forward and backward pump sources, respectively. The total pump power is only 95.7 mW.
High Pump Conversion Efficiency and Broad L-Band ASE Sourceby Using Sagnac Feedback Loop

蒋俏峰,刘小明,倪屹,王青

DOI: https://doi.org/10.3321/j.issn:0258-7025.2004.06.017

2004-01-01

Chinese Journal of Lasers

Abstract:Optical wideband source of L-band amplified spontaneous emission (ASE) from erbium doped fiber has extensive application in fiber sensors and device testing; here the pump power conversion is one of the key technique. In this work, based on the secondary pumping mechanism by C-band power for L-band signal, a Sagnac loop is used to feed-back the output of C-band ASE, the reflected C-ASE propagates along single direction in the fiber and is amplified in expending inversion population, so that the utility of pump power for L-band ASE is increased. Experimentally, the total output power was 14 dBm at 125 mW 980 nm pumping i.e. pump power conversion efficiency up to 20% was achieved. Without gain flatten filter, the 1 dB bandwidth was 31.1 nm (1568.9～1600 nm), so that high pump conversion efficiency and broad L-band ASE source was demonstrated.
Band selective C− or C+L-band ASE source using the backward feedback technique

Xiulin Wang,Wencai Huang,Huiying Xu,Zhiping Cai

DOI: https://doi.org/10.1109/CLEOPR.2009.5292494

2009-01-01

Abstract:We present a C- or C+L-band selective ASE source using the 1times2 optical switch in a bi-directional pumping configuration. The 25.9 mW C-band or 22.5 mW C+L-band ASE spectrum is obtained merely by control the state of the optical switch.
High Power L-Band Erbium-Doped Fiber Laser Pumped by A C-Band Superfluorescent Source

S. -P. Chen,Y-G. Li,K. -C. Lu,S. -H. Zhou,Z. -J. Liu

DOI: https://doi.org/10.1002/lapl.200710094

IF: 1.704

2007-01-01

Laser Physics Letters

Abstract:The C-band is demonstrated to be suitable for pumping L-band erbium-doped fiber laser (EDFL) with a broad pumping band. A high power C-band superfluorescent fiber source (SFS) peaked at 1545 nm with output power of 1.86 W is constructed and utilized as pump source for L-band EDFL. Based on this, an all single-mode-fiber L-band EDFL emitting at 1591.9 nm with 1.19 W output power is obtained. The laser exhibits a high conversion efficiency of 64.0% with a high ASE extinction ratio of 66 dB and a narrow bandwidth of less than 0.08 nm.
Soa-Pumped Erbium-Doped Ase Fibre Source with Flattened Spectrum and High Power Density

Y. Jiang,C. Tang,B. Yang

DOI: https://doi.org/10.1049/el.2009.0048

2009-01-01

Electronics Letters

Abstract:A spectrum-flattened two-stage amplified spontaneous emission (ASE) fibre source is proposed and experimentally demonstrated. The source is structured by an erbium-doped fibre simultaneously pumped by a 980 nm laser and a semiconductor optical amplifier (SOA) source. In the wavelength range of 1526-1563 nm, a spectrum ripple of +/- 0.5 dB and an average power density of -14 dBm/0.1 nm are achieved.
933 W Yb-doped Fiber ASE Amplifier with 504 Nm Bandwidth

Ping Yan,Junyi Sun,Dan Li,Xuejiao Wang,Yusheng Huang,Mali Gong,Qirong Xiao

DOI: https://doi.org/10.1364/oe.24.019940

IF: 3.8

2016-01-01

Optics Express

Abstract:In this paper, a 933 W amplified spontaneous emission (ASE) source with a full width at half maximum (FWHM) of 50.4 nm is presented. The broadband source is generated by a 1271 W ASE amplifier together with 140m ordinary passive fiber for nonlinear transformation. With multi-wavelength rate equations and a nonlinear Schrödinger equation (NLSE), spectral evolution of the ASE source is analyzed theoretically.
L-band all-optical gain-clamped erbium-doped fiber amplifier via ASE reflection technique

Hao Zhang,Qingying Dou,Yanli Jin,Tuan Guo,Lihui Liu,Yange Liu,Shuzhong Yuan,Xiaoyi Dong

DOI: https://doi.org/10.1002/mop.21496

IF: 1.311

2006-01-01

Microwave and Optical Technology Letters

Abstract:We present an L-band all-optical gam-clamped erbium-doped fiber amplifier with a fiber-loop mirror as the ASE reflector. By using the combination of a C/L-band wavelength division multiplexer (WDM) and fiber-loop mirror, the backward C-band amplified spontaneous emission (ASE) is reflected back into the erbium-doped fiber and works (is the control light. The static gain level of this amplifier call be adjusted by changing the ASE feedback The experimental results show that the EDFA gain can be effeciively clamped via this ASE reflection technique. (c) 2006 Wiley Periodicals, Inc.

A C+L-band Erbium-Doped Fiber ASE Source Using Dual-Forward Pumping Configuration

Low-Ripple and High-Efficiency C+L-Band Erbium-Doped Fiber Amplified-Spontaneous-Emission Sources Using A Dual Forward Pumping Configuration

A Double-pass Erbium-doped Fiber Based Broadband ASESource by Utilizing C-band ASE Compensation

Theoretical and Experimental Analysis of Bidirectionally Pumped 1.3 Μm Pr3+-doped ASE Source

C+L-Band Erbium-Doped Fiber Broadband Light Source Using One-Stage Configuration

Simulation Analysis of One-Stage C+L-band Erbium-Doped Fiber ASE Source with Double-Pass Bi-Directional Pumping Configuration

A Novel Two-Stage Erbium Amplified Spontaneous Emission Fiber Source with 80nm Bandwidth

Characteristics of the dual-forward pumped L-band ASE fiber source

Design and Optimization of a High-Power L-band ASE Fiber Source

A Selective C and L-Band Amplified Spontaneous Emission Source Using a 1×2 Optical Switch

Characteristics Comparison of Optimal L-Band Er-Doped Ase Sources in Different Configurations

Band Selective ASE Source for Dual-Band DWDM Device Characterization and Metro Networks

A C-or C+L-Band Selectable ASE Source Using the Backward Feedback Technique with an Optical Switch

Resonantly Pumped High Power Flat L-band Erbium-Doped Superfluorescent Fiber Source

A Novel Conventional/Long-Band Erbium-Doped Fibre Amplified Spontaneous Emission Source With 80 Nm Bandwidth

High Pump Conversion Efficiency and Broad L-Band ASE Sourceby Using Sagnac Feedback Loop

Band selective C− or C+L-band ASE source using the backward feedback technique

High Power L-Band Erbium-Doped Fiber Laser Pumped by A C-Band Superfluorescent Source

Soa-Pumped Erbium-Doped Ase Fibre Source with Flattened Spectrum and High Power Density

933 W Yb-doped Fiber ASE Amplifier with 504 Nm Bandwidth

L-band all-optical gain-clamped erbium-doped fiber amplifier via ASE reflection technique