Abstract:The aim of this work is to investigate the effect of heat treatment (T6) on the microstructure, mechanical, and corrosion properties of Al 319.0 alloy. In particular, Al 319.0 alloy is developed by squeeze casting using 200 MPa pressure, and further the ingots are solutionized, quenched and artificially aged to develop a homogenous microstructure, improve distribution of secondary phase(s), and mechanical properties at ambient and elevated temperatures. The phase and microstructure of the as-cast and heat-treated Al 319.0 alloys analyzed using X-ray diffraction, optical microscope, and field emission scanning electron microscope illustrate cast ingot contain α -Al as a primary phase and Al 2 Cu, eutectic Si, and Al 5 Si 7 Cu-containing intermetallic as secondary phase(s). However, heat treatment leads to complete dissolution of Al 5 Si 7 Cu and partial dissolution and re-precipitation of Al 2 Cu phase. Moreover, heat treatment changes the morphology of eutectic Si into spheroidal Si, blocky Al 2 Cu into spheroids Al 2 Cu, and the heat-resistant α (FeMn), Al 8 Cu 3 Mn(Si) phases emerged. The tensile test at room and elevated temperatures exhibit significant improvement in the YS and UTS at ambient temperature in heat-treated alloy owing to the presence of precipitation-hardened phases. Importantly, these phases are found stable up to 150 °C and tend to coarsen at 250 °C owing to thermal softening invariably leading to a substantial reduction in mechanical properties. Potentiodynamic polarization and electrochemical impedance spectroscopy shed light on galvanic corrosion phenomena predominant in 0.1 M NaCl solution. In particular, heat-treated alloy specimens demonstrated the lowest corrosion current ( I corr —~1.72 μA/cm 2 ) , and highest polarization resistance ( R p —12260 Ω.cm 2 ) implying superior corrosion resistance as compared to as-cast alloy owing to protective barrier provided by finer Al 2 Cu precipitates and spheroidal Si.

Effects of T6 heat treatment with residual heat of casting on microstructure and mechanical properties of 319 aluminium alloy castings

Effect of heat treatment on microstructure and tensile properties of 319 aluminum alloy

Effect of short T6 heat treatment on the microstructure and the mechanical properties of newly developed die-cast Al–Si–Mg–Mn alloys

Research on the Remained Heat Treatment Technique of Casting 319 Aluminum Alloys

Effects of heat treatment and testing temperature on the tensile properties of Al–Cu and Al–Cu–Si based alloys

Effects of Heat Treatment on Mechanical Properties of VAR- Cast Ti-6Al-4V Alloy

Effects of heat treatment on the microstructures and mechanical properties of as-cast Ti-45Al-2Nb-2Cr-(0.2, 0.5) C alloys

Effect of T6 heat treatment on microstructure and mechanical properties of large-weight aluminum alloy flywheel housing parts formed by local-loading squeeze casting

Influence of Y Content and T6 Heat Treatment on the Organization and Mechanical Properties of Cast A356 Aluminum Alloy

The Effect of Heat Treatments on the Microstructural Evolution of Twin-Roll-Cast Al-Fe-Si Alloys

Effect of heat treatment on the microstructure and mechanical properties of Al‐9Si‐0.4Mg‐0.1Cu alloy

Effect of T6I6 treatment on dynamic mechanical behaviour of Al-Si-Mg-Cu cast alloy and impact resistance of its cast motor shell

Effect of Heat Treatment on Microstructure, Mechanical, and Corrosion Properties of Squeeze Cast Al 319.0 Alloy

Effects of different heat treatment temperatures on the microstructure and mechanical properties of additive manufacturing Ti65 alloys

Effect mechanism of Sc addition and T6 heat treatment on precipitated phase and mechanical properties of Al‐Cu‐Mn alloy

Mechanism of cryogenic, solid solution and aging compound heat treatment of die-cast Al alloys considering microstructure variation

The Effect of Heat Treatment on the Microstructure and Mechanical Properties of Powder Metallurgy Ti-48Al Alloy

The Influence of T6 Treatment on Fracture Behavior of Hypereutectic Al-Si HPDC Casting Alloy

Effect of chemical composition and T6 heat treatment on microstructure and mechanical properties of a hyper eutectic Al–Si alloy

Effect of heat treatment on microstructure and mechanical properties of Cu–6.9Ni–2.97Al–0.99Fe–1.06Mn alloy

The effect of T4 and T6 heat treatments for dynamic impact behavior of casting Mg-Gd-based alloys