Abstract:To determine the ash characteristics during fluidized bed combustion and gasification purposes, the investigation of the impacts of chemical composition of Jincheng coal ash on the sintering temperature was conducted. A series of experiments on the sintering behavior at 0.5 MPa was performed using the pressurized pressure-drop technique in the combustion and gasification atmospheres. Meanwhile, the mineral transformations of sintered ash pellets were observed using X-ray diffractometer (XRD) analyzer to better understand the experimental results. In addition, quantitative XRD and field emission scanning electron microscope/energy dispersive X-ray spectrometer (FE-SEM/EDS) analyses of ash samples were used for clarifying the detailed ash melting mechanism. These results show that the addition of Fe2O3 can obviously reduce the sintering temperatures under gasification atmospheres, and only affect a little the sintering temperature under combustion atmosphere. This may be due to the presence of iron-bearing minerals, which will react with other ash compositions to produce low-melting-point eutectics. The FE-SEM/EDS analyses of ash samples with Fe2O3 additive show consistent results with the XRD measurements. The CaO and Na2O can reduce the sintering temperatures under both the combustion and gasification atmospheres. This can be also contributed to the formation of low-melting-point eutectics, decreasing the sintering temperature. Moreover, the fluxing minerals, such as magnetite, anhydrite, muscovite, albite and nepheline, contribute mostly to the reduction of the sintering temperature while the feldspar minerals, such as anorthite, gehlenite and sanidine, can react with other minerals to produce low-melting-point eutectics, and thereby reduce the sintering temperatures.

Particularities Concerning Sintered Ash Deposits along Flue Ways of CFB Waste Incinerators

The Characterization of Sintering Deposit on the Heat-Transfer Surface of CFB Municipal Solid Waste Incinerator

Analysis of Formation and Growth Process of Ash Deposition on the Convective Heating Surface of a 400t/d MSW Incinerator Based on Different Operating Days

Mechanism of Na2O/CaO Ratio Affecting Ash Fusing Characteristics During Ash Deposition and Slagging in Municipal Solid Waste Incinerator

Sintering and Deposition Characteristics of Ashes with High Calcium and Chlorine Content from a Medical Wastes Incinerator

Characteristics Investigation of the Solid Residues from CFB Municipal Solid Waste Incinerator

Mechanism Analysis of Ash Deposits Corrosion in Waste Incinerator

Sintering Behavior Of Ash From Combustion Of Jincheng Coal And Pine Sawdust Blends

In-situ sampling investigation of deposition and corrosion of convective heating surfaces in a grate type municipal solid waste incineration plant: a case study

Microanalysis of solid residues from coal slurry fired furnace

Characteristics and mechanism of slagging in a 500 t/d MSW incinerator

Analysis on Deposition Mechanism of Ash with High Ash Fusion Temperatures on the Heat-insulation Layer in Boiler

Microstructures Of Chinese Coal Ashes Derived From Combustion

Compositional and structural study of ash deposits spatially distributed in superheaters of a large biomass-fired CFB boiler

Research on Sintering and Fusion Characteristics of Several Representative Coal Ashes

Influence of Ash Composition on the Sintering Behavior During Pressurized Combustion and Gasification Process

On-the-spot Test of the Slagging in a Grate-circulating Bed Garbage Incinerator Superheater

Mechanism Research on the Development of Ash Deposits on the Heating Surface of Biomass Furnaces

SEM/EDS and XRD characterization of raw and washed MSWI fly ash sintered at different temperatures.

Study of Ashes from a Medical Waste Incinerator in China: Physical and Chemical Characteristics on Fly Ash, Ash Deposits and Bottom Ash

ICOPE-15-C055 Investigation on Slagging and Fouling of HRSG for Ferrosilicon Electric Furnace