Abstract:Heat treatment process is one of the key methods to improve the mechanical properties of age-hardening Al-Cu-Li alloy, and pre-stretching can further increase nucleation sites of precipitates by introducing dislocations. In this study, the effects of solution treatment, artificial ageing, and 4% pre-stretching on the microstructure evolution, mechanical properties, and fracture mechanism of extruded 2050 Al-Cu-Li alloy were investigated. The results indicated that the residual secondary phase, including Al2Cu and Al2CuLi, precipitated in hot extrusion were dissolved and a non-recrystallization characteristic for the 2050 alloy was presented after solution treated at 530 degrees C for 90 min. During artificial ageing at 150 degrees C, the precipitation sequence of the alloy without pre-stretching was: SSS -> GP zone + delta'/beta'->theta' + T-1. Pre-stretching led to denser dislocations thus a higher nucleation rate of T-1 phase in compared with the alloy without pre-stretching. Additionally, the segregations of non-Cu atom at dislocations inhibited the formation of GP zones in the early ageing state, thereby providing sufficient Cu atoms for accelerating the growth of T1 phases. After pre-stretched by 4% and aged at 150 degrees C for 12 h, a good combination of strength (YS = 671 MPa, UTS = 682 MPa) and ductility (EL = 10.3%) was obtained. The fracture mode changed from transgranular fracture to intergranular fracture with increasing ageing time due to the dislocation density and the distribution, size, and number density of the precipitates.

Effects of Heat Treatment on Microstructure and Mechanical Properties of Al-5Cu Alloys in Direct Squeezing Casting

Research on Characteristics of Heat Treatment of Squeeze Cast Al-Cu-Mg Alloy

Microstructures and Mechanical Properties of a Squeeze-Casted Al-Zn-Mg-Cu Alloy after Heat Treatment

Micro-mechanism of Simultaneous Improvement of Strength and Ductility of Squeeze-Cast Al–Cu Alloy

Effect of heat treatment on microstructure and tensile properties of 319 aluminum alloy

Microstructure and mechanical properties of squeeze-cast Al−5.0Mg−3.0Zn−1.0Cu alloys in solution-treated and aged conditions

Effects of under-aging treatment on microstructure and mechanical properties of squeeze-cast Al-Zn-Mg-Cu alloy

Effect of Solutionising and Ageing on the Microstructure and Mechanical Properties of a High Strength Die-Cast Al–Mg–Zn–Si Alloy

Microstructural Evolution and Strengthening Behavior of High-Pressure Die-Cast High-Cu Al-Si-Cu-Mg Alloy with T5 Treatment

Effect of Mg and Cu Additions on Microstructure and Mechanical Properties of Squeeze Casting Al-Si-Cu-Mg Alloy

Effects of T6 heat treatment with residual heat of casting on microstructure and mechanical properties of 319 aluminium alloy castings

Microstructure and Mechanical Properties of Cast Al-Si-Cu-Mg-Ni-Cr Alloys: Effects of Time and Temperature on Two-Stage Solution Treatment and Ageing

Effect of Heat Treatment on the Microstructure and Mechanical Properties of Extruded Al–4Cu–1Li–0.4Mg–0.4Ag–0.18Zr Alloy

Effects of Heat Treatment and Pre-Stretching on the Mechanical Properties and Microstructure Evolution of Extruded 2050 Al–Cu–Li Alloy

Effect of heat treatment on the microstructure and mechanical properties of Al‐9Si‐0.4Mg‐0.1Cu alloy

Role of Heat Treatment in the Improvement of Mechanical Properties of a High-Quality Al-11Si- 1.5Cu-0.3Mg Casting Alloy

Effects of Solution Treatment on the Microstructure, Tensile Properties, and Impact Toughness of an Al–5.0Mg–3.0Zn–1.0Cu Cast Alloy

Effect of Solution Treatment on Microstructures and Mechanical Properties of Centrifugal Casting Al-Cu Alloy

Microstructure and Properties of Solution Heat-Treated Al-Si-Cu Alloy by Squeeze Casting

Effect of heat treatment on microstructure and mechanical properties of Cu–6.9Ni–2.97Al–0.99Fe–1.06Mn alloy

Effect of Aging Treatment on High Temperature Mechanical Properties of a Cast Al–Li–Cu Alloy