Abstract:Aluminum high pressure die casting (HPDC) technology has evolved in the past decades, enabling stronger and larger one-piece casting with significant part consolidation. It also offers a higher design freedom for more mass-efficient thin-walled body structures. For body structures that require excellent ductility and fracture toughness to be joined with steel sheet via self-piercing riveting (for instance, shock towers and hinge pillars, etc.), a costly T7 heat treatment comprising a solution heat treatment at elevated temperatures (450 Â°Câ€“500 Â°C) followed by an over-ageing heat treatment is needed to optimize microstructure for meeting product requirement. To enable cost-efficient mass production of HPDC body structures, it is important to eliminate the expensive T7 heat treatment without sacrificing mechanical properties. Optimizing die cast alloy chemistry is a potential solution to improve fracture toughness and ductility of the HPDC components. The present study intends to tailor the Mg and Cu additions for a new Al-Si-Cr type die casting alloy (registered as A379 with The Aluminum Association, USA) to achieve the desired tensile properties without using T7 heat treatment. It was found that Cu addition should be avoided, as it is not effective in enhancing strength while degrades tensile ductility. Mg addition is very effective in improving strength and has minor impact on tensile ductility. The investigated Al-Si-Cr alloy with a nominal composition of Al-8.5wt.%Si-0.3wt.%Cr-0.2wt.%Fe shows comparable tensile properties with the T7 treated AlSi10MnMg alloy which is currently used for manufacturing shock towers and hinge pillars.

Effect of Mg and Cu Additions on Microstructure and Mechanical Properties of Squeeze Casting Al-Si-Cu-Mg Alloy

Effect of Mg addition on microstructure and mechanical properties of Al-Si-Cu-Fe alloy with squeeze casting

Microstructure and mechanical properties of squeeze-cast Al−5.0Mg−3.0Zn−1.0Cu alloys in solution-treated and aged conditions

Effects of magnesium and copper additions on tensile properties of Al-Si-Cr die casting alloy under as-cast and T5 conditions

Developing high performance squeeze cast Al-Cu alloys with high Fe and Cu contents

Study on Microstructure Distribution of Al-Cu-Mg Alloy in Squeeze Casting Process

Microstructural refinement and tensile properties enhancement of Al-10Mg2Si cast alloys by copper addition

Effects of Zr and Mg alloying on microstructure and properties of Cu-Cr-Si alloys

The Microstructure, and Mechanical and Corrosion Properties of As-Cast and As-Extruded Mg-2%Zn-x%Cu Alloys After Solution and Aging Heat Treatments

Effect of Casting Process and Thermal Exposure on Microstructure and Mechanical Properties of Al-Si-Cu-Ni Alloy

Effects of under-aging treatment on microstructure and mechanical properties of squeeze-cast Al-Zn-Mg-Cu alloy

Effects of Mg content on microstructure and mechanical properties of low Zn-containing Al−xMg−3Zn−1Cu cast alloys

The effect of Si addition on the microstructure and tensile properties of casting Al-5.0Cu-0.6Mn-1.2Fe alloys

Effects of Adding Trace Modification Elements and Heat Treatment on the Strength and Toughness of AlSi8Cu2MgMn Alloy

Effect of Low Cu Content and Heat Treatment on the Microstructure and Mechanical Properties of High-Vacuum Die-Cast AlSiMgMn Alloys

Evolution of the microstructure and properties of a Cu–Cr-(Mg) Alloy upon thermomechanical treatment

Microstructure and Mechanical Properties of Squeezing Casting Mg-Nd-Gd-Zn-Zr Alloy

Effect of heat treatment on the microstructure and mechanical properties of Al‐9Si‐0.4Mg‐0.1Cu alloy

Achievement of High Strength and Ductility in Al–Si–Cu–Mg Alloys by Intermediate Phase Optimization in As-Cast and Heat Treatment Conditions

The combined effect of pre-aging and Mg/Si ratio on the natural aging and bake hardening in Al-Mg-Si-0.7Cu alloys

Effect of Cu addition on precipitation and age-hardening response of an Al-15%Mg2Si alloy