Abstract:The use of high strength low alloy steels provides several potential advantages including lower weight, lower manufacturing costs, and ease of handling and transport. The progress in steel manufacturing technology has continually called for new developments in welding processes and consumables to produce weld metal deposits with mechanical properties essentially equivalent to the base metal. Controlling the weld metal microstructures as well as raising the welding productivity is critical factor for the development of weld metal of high strength steel to secure satisfactory mechanical properties and to reduce production costs. In order to meet the demand to apply 1000 MPa class steel to the fabrication of large scale steel structures, a weld wire for the 1000 MPa class steel has been under development to obtain the required strength and toughness, which depend primarily on the microstructure. In this work, the effects of shielding gas composition on the microstructure and properties of 1000 MPa grade deposited metals produced by metal active gas (MAG) welding have been investigated. The shielding gas employed was a mixture of argon (Ar) and carbon dioxide (CO2) (5%similar to 30%), and the weld heat input was 13 kJ/cm. The properties of deposited metal with shielding gas of 80%Ar+20%CO2 is the best, the yield strength is 980 MPa, meanwhile, its Charpy absorbed energy at room temperature and -40 degrees C are 72.6 and 52 J, respectively. The results show that the microstructure of the deposited metal, consisting primary of low carbon martensite and a few parallel bainite plate, became more interweaved bainitic packets as the CO2 content of the shielding gas was increased. The initial bainite nucleated at austenite grain boundaries and subsequent bainite plates can form at the oxide inclusions of intragranular, which presented an intersected configuration and the microstructure was refined. The content of bainite palte and distribution morphology of martensite/bainite is the intrinsic reason attributed to mechanical properties of deposited metals. The content of bainite for deposited metal has an optimal proportion and more isn't necessarily better. It was also found that the area fraction, the size and the compositions of oxide inclusions in deposited metals were changed with increasing CO2 content. The deposited metal as using 70%Ar+30%CO2 has the minimum toughness because more large size oxide inclusions formed which are known to be harmful to the toughness.

Influence Of Shielded Gas Flow In Co2 Laser Welding Of A5083 Aluminum Alloy

Effect of Shielding Gas on Surface Formation During Laser Welding of Al-Si Coated Press-Hardened Steels

Experimental and Numerical Investigation of Shielding Gas Behaviors in Laser Welding of TC4 Alloy

Study on Side Assist Blowing Gas with Different Composition in High Power CO_2 Laser Welding

Active control effect of shielding gas flow on high-power fiber laser welding plume

Influence of CO2 laser welding process on weld surface formation of wrought magnesium alloy AZ31B

Effect of activating flux Cr2O3 on microstructure and properties of laser welded 5083 aluminum alloys

Effect of Shielding Gas on the Plasma Plume in Pulsed Laser Welding

Effects of He-Ar shielding gas compositions on arc plasma physical properties in rotating laser + GMAW hybrid fillet welding: Numerical simulation

Influence of CO_2 laser-MIG hybrid welding process on weld formation of 6005A aluminum alloy

Effect of Shielding Conditions on Welding Properties in Underwater Local-Dry Laser Welding

EFFECT OF SHIELDING GAS ON MICROSTRUCTURE AND PERFORMANCE OF 1000 MPa GRADE DEPOSITED METALS

Investigating the Influence Mechanism of Different Shielding Gas Types on Arc Characteristics and Weld Quality in TA2 Laser–Arc Hybrid Welding

Larger-area Alloying of CSiB+NiMoCo on Carbon Steel by a 45-Kw CO 2 Laser: Effect of Protection Gas on Process and Microstructure

Thermal and Fluid Flow Characteristics and their Relationships with Porosity in Laser Welding of AA5083

Effects of Ar-N 2 -He shielding gas on microstructure, mechanical properties and corrosion resistance of the Laser-MIG additive manufacturing 316L stainless steel

Influence of Shielding Gas on Microstructure and Properties of GMAW DSS2205 Welded Joints

Weldability improvement by wobbling technique in high power density laser welding of two aluminum alloys: Al-5052 and Al-6061

Modeling and numerical study of keyhole-induced porosity formation in laser beam oscillating welding of 5A06 aluminum alloy

Investigation on Porosity Suppression in Deep-Penetration Laser Welding by Using Computational Fluid Dynamics