Abstract:The use of high strength low alloy steels provides several potential advantages including lower weight, lower manufacturing costs, and ease of handling and transport. The progress in steel manufacturing technology has continually called for new developments in welding processes and consumables to produce weld metal deposits with mechanical properties essentially equivalent to the base metal. Controlling the weld metal microstructures as well as raising the welding productivity is critical factor for the development of weld metal of high strength steel to secure satisfactory mechanical properties and to reduce production costs. In order to meet the demand to apply 1000 MPa class steel to the fabrication of large scale steel structures, a weld wire for the 1000 MPa class steel has been under development to obtain the required strength and toughness, which depend primarily on the microstructure. In this work, the effects of shielding gas composition on the microstructure and properties of 1000 MPa grade deposited metals produced by metal active gas (MAG) welding have been investigated. The shielding gas employed was a mixture of argon (Ar) and carbon dioxide (CO2) (5%similar to 30%), and the weld heat input was 13 kJ/cm. The properties of deposited metal with shielding gas of 80%Ar+20%CO2 is the best, the yield strength is 980 MPa, meanwhile, its Charpy absorbed energy at room temperature and -40 degrees C are 72.6 and 52 J, respectively. The results show that the microstructure of the deposited metal, consisting primary of low carbon martensite and a few parallel bainite plate, became more interweaved bainitic packets as the CO2 content of the shielding gas was increased. The initial bainite nucleated at austenite grain boundaries and subsequent bainite plates can form at the oxide inclusions of intragranular, which presented an intersected configuration and the microstructure was refined. The content of bainite palte and distribution morphology of martensite/bainite is the intrinsic reason attributed to mechanical properties of deposited metals. The content of bainite for deposited metal has an optimal proportion and more isn't necessarily better. It was also found that the area fraction, the size and the compositions of oxide inclusions in deposited metals were changed with increasing CO2 content. The deposited metal as using 70%Ar+30%CO2 has the minimum toughness because more large size oxide inclusions formed which are known to be harmful to the toughness.

Effect of Shielding Gas on Surface Formation During Laser Welding of Al-Si Coated Press-Hardened Steels

Effect of Shielding Gas on Surface Formation During Laser Welding of Al-Si Coated Press-Hardened Steels

Influence of Shielding Gas on Microstructure and Mechanical Properties of Laser Welded–brazed Al/steel Lapped Joint

Effects of Shielding Gases on Process Stability of 10crni3mov Steel in Hybrid Laser-Arc Welding

Effect of Al Si coating on laser spot welding of press hardened steel and process improvement with annular stirring

Effect of Al-Si Coating on the Interfacial Microstructure and Corrosion Resistance of Dissimilar Laser Al Alloy/22MnB5 Steel Joints

Comparison Investigation on Microstructure and Properties of Dissimilar Welds by Laser Alignment Welding and Laser Offset Welding Between Al–Si Coated 1.5 GPa and Novel 2 GPa Press Hardened Steels

Analysis on surface morphology formation process of Al-Si coated 22MnB5 steel during laser welding

Effect of Al-Si Coating on Weldability of Press-Hardened Steels

Suppression of δ-ferrite formation on Al-Si coated press-hardened steel during laser welding

Influence of Shielding Gas Pressure on Welding Characteristics in CO2 Laser-Mig Hybrid Welding Process

Effect of shielding gas on MIG welding performance with austenitic wire

Microstructure and mechanical properties of laser welded hot-press-formed steel with varying thicknesses of Al-Si coatings cleaned by nanosecond pulsed laser

EFFECT OF SHIELDING GAS ON MICROSTRUCTURE AND PERFORMANCE OF 1000 MPa GRADE DEPOSITED METALS

Influence of Shielding Gas on Microstructure and Properties of GMAW DSS2205 Welded Joints

Influence of CO2 laser welding process on weld surface formation of wrought magnesium alloy AZ31B

Effect of Shielding Gas on the Microstructure and Properties of Laser-MAG Hybrid Welded Joint for Nickel-Saving Stainless Steel

Effect of Different Coatings on the Weldability of Al to Steel

A Study On Microstructure And Properties Of Phs Fiber Laser Welded Joints Obtained In Air Atmospheres

Experimental and Numerical Investigation of Shielding Gas Behaviors in Laser Welding of TC4 Alloy

Microstructure and Mechanical Properties of Laser Welded Al-Si Coated Hot-Press-Forming Steel Joints.