Abstract:Laser welding of magnesium alloy is still challenging because of the frequently occurred defects. In this work, a promising vacuum laser welding technique was used to join AZ31 magnesium alloy. The effect of ambient pressure on weld surface appearances and weld fusion cross sections was symmetrically investigated. It was found that the penetration depth increased and the weld width became narrower with the descending of ambient pressure from 101 kPa to 10 kPa. However, the penetration depth did not increase and even decreased when the ambient pressure further decreased to 1 kPa and 0.1 kPa. In addition, hump defects occurred at lower ambient pressure of 1 kPa and 0.1 kPa. The weld pool and keyhole behaviors were in-site observed using a high-speed camera at various ambient pressures. The results showed that unstable keyhole and turbulent flow were found in the molten pool at 101 kPa. The keyhole became more stable as the ambient pressure decreased from 101 kPa to 10 kPa. When the ambient pressure further decreased to 1 kPa and 0.1 kPa, the liquid metal thickness between keyhole wall and weld pool periphery became very narrow, which sometimes resulted in unstable absorption of the laser energy. Finally, a 10 mm-thick bottom-locking weld was made under vacuum. The average grain diameter of the weld in vacuum is 28.4 μm, which is much lower than 46 μm in atmosphere. The tensile results showed that the average ultimate tensile strength and the elongation of the joints welded in vacuum at 10 kPa was 8.8 % and 44.0 % higher than that of the joints welded in atmosphere respectively. The enhanced mechanical properties were attributed to the reduced porosity and refined microstrustures of the weld joint made under vacuum.

Influence of CO2 laser welding process on weld surface formation of wrought magnesium alloy AZ31B

Welding Modes and Weld Formation Characteristics of CO2 Laser Welding of Wrought Magnesium Alloy AZ31B

Experimental Study on Pores in Laser Welding of Magnesium Alloys

Impact of power modulation on weld appearance and mechanical properties during laser welding of AZ31B magnesium alloy

Effects of Welding Parameters on Weld Porosity During CO2 Laser Welding of Die-Cast Magnesium Alloys

Microstructure homogeneity and mechanical properties of laser-arc hybrid welded AZ31B magnesium alloy

Effect of nanosecond pulse laser power on welding interface and mechanical properties of AZ31B Mg/6061 Al

Effect of laser power on microstructure and mechanical properties of laser heat conduction lap welded joint between AZ31B magnesium alloy and DP780 galvanized steel

Formation and mechanical properties of AZ31B magnesium alloy welds by power-modulated oscillating laser

The Influence of Heat and Cryogenic Treatment on Microstructure Evolution and Mechanical Properties of Laser-Welded AZ31B

Effect of preheating temperature on the microscopic structure and mechanical performance of pulsed laser welding in sheet AZ31 alloy

Effect of Shielding Gas on Surface Formation During Laser Welding of Al-Si Coated Press-Hardened Steels

Investigation of interfacial microstructure and connection mechanism of magnetic field-assisted magnesium/aluminum laser welding joint

Microstructure – Properties relationship in laser-welded AZ31B magnesium alloy

Effect of pulse overlap rate on the microstructure and mechanical properties of laser welds of thin AZ31 magnesium alloy

The influence of laser power on microstructure and properties of laser welding-brazing of Al alloys to Al-Si coated 22MnB5 steel

Vacuum laser beam welding of AZ31 magnesium alloy: Weld formability, microstructure and mechanical properties

Microstructure and Mechanical Properties of Laser Welded Magnesium Alloy/Steel Joint Using Cu-Si Composite Interlayer

On the heterogeneous microstructure and strengthening mechanisms in a laser welding AZ80 magnesium alloy

Influence of CO_2 laser-MIG hybrid welding process on weld formation of 6005A aluminum alloy