Abstract:The use of high strength low alloy steels provides several potential advantages including lower weight, lower manufacturing costs, and ease of handling and transport. The progress in steel manufacturing technology has continually called for new developments in welding processes and consumables to produce weld metal deposits with mechanical properties essentially equivalent to the base metal. Controlling the weld metal microstructures as well as raising the welding productivity is critical factor for the development of weld metal of high strength steel to secure satisfactory mechanical properties and to reduce production costs. In order to meet the demand to apply 1000 MPa class steel to the fabrication of large scale steel structures, a weld wire for the 1000 MPa class steel has been under development to obtain the required strength and toughness, which depend primarily on the microstructure. In this work, the effects of shielding gas composition on the microstructure and properties of 1000 MPa grade deposited metals produced by metal active gas (MAG) welding have been investigated. The shielding gas employed was a mixture of argon (Ar) and carbon dioxide (CO2) (5%similar to 30%), and the weld heat input was 13 kJ/cm. The properties of deposited metal with shielding gas of 80%Ar+20%CO2 is the best, the yield strength is 980 MPa, meanwhile, its Charpy absorbed energy at room temperature and -40 degrees C are 72.6 and 52 J, respectively. The results show that the microstructure of the deposited metal, consisting primary of low carbon martensite and a few parallel bainite plate, became more interweaved bainitic packets as the CO2 content of the shielding gas was increased. The initial bainite nucleated at austenite grain boundaries and subsequent bainite plates can form at the oxide inclusions of intragranular, which presented an intersected configuration and the microstructure was refined. The content of bainite palte and distribution morphology of martensite/bainite is the intrinsic reason attributed to mechanical properties of deposited metals. The content of bainite for deposited metal has an optimal proportion and more isn't necessarily better. It was also found that the area fraction, the size and the compositions of oxide inclusions in deposited metals were changed with increasing CO2 content. The deposited metal as using 70%Ar+30%CO2 has the minimum toughness because more large size oxide inclusions formed which are known to be harmful to the toughness.

A novel approach to optimize weld formation and regulate interfacial microstructure in TC4/304SS dissimilar arc welding by active hybrid shielding gas

Dissimilar gas tungsten arc welding of TC4 titanium to 304 stainless steel using CuSi3 filler wire

Weld Formation Mechanism and Microstructural Evolution of TC4/304 Stainless Steel Joint with Cu-Based Filler Wire and Preheating

Microstructure and Mechanical Properties of Dissimilar TC4 Titanium Alloy/304 Stainless Steel Joint Using Copper Filler Wire

Influence of Shielding Gas on Microstructure and Mechanical Properties of Laser Welded–brazed Al/steel Lapped Joint

Optimization of Welding Parameters During Ti-TA2/5A06Al Dissimilar Double-Sided Cold Arc Metal Inert Gas Welding

Microstructure and mechanical property improvement of Ti alloy and stainless steel joint based on a hybrid connection mechanism

EFFECT OF SHIELDING GAS ON MICROSTRUCTURE AND PERFORMANCE OF 1000 MPa GRADE DEPOSITED METALS

Study on the microstructure optimization and mechanical properties of dissimilar TC4-304L arc-brazing joints

Effects of Shielding Gases on Process Stability of 10crni3mov Steel in Hybrid Laser-Arc Welding

Effect of shielding gas on MIG welding performance with austenitic wire

Microstructure and Mechanical Properties of Cold Metal Transfer Welding-Brazing of Titanium Alloy (TC4) to Stainless Steel (304L) Using V-shaped Groove Joints

Microstructure, Corrosion and Mechanical Properties of TiC Particles/Al-5Mg Composite Fillers for Tungsten Arc Welding of 5083 Aluminum Alloy

A novel high entropy composite interlayer for diffusion bonding of TC4 titanium alloy to 316 L stainless steel

Developing high-strength titanium/steel composite structures by adding composite interlayer

Effects of Pre‐Placed Nano‐TiC Powder on the Performance of Steel/Aluminum Laser Welded Joints

Experimental Study on Welding Characteristics of Co2 Laser Tig Hybrid Welding Process

Dissimilar metal joining of Q235 mild steel to Ti6Al4V via resistance spot welding with Ni-Cu interlayer

Joining mechanism evolution of fusion welded TC4 titanium alloy/304 stainless steel dissimilar joint by GTAW

Effects of Thermal Distribution Strategy on a Ti-6Al-4V/304L Dissimilar Joint Fabricated Using the Variable Polarity Cold Metal Transfer Arc-Brazing Method

Experimental and numerical study on microstructure and mechanical properties for laser welding-brazing of TC4 Titanium alloy and 304 stainless steel with Cu-base filler metal