Abstract:This Ph.D. research is based on the development of novel sol-gel techniques for synthesis of nanostructured ultra high temperature ceramics (UHTCs) and subsequent spark plasma sintering (SPS) for densifying the UHTC composites. The liquid nature of the sol-gel process offers advantages such as high purity and ability for mixing and infiltration, and thus it can overcome some shortcomings of the conventional power processing of ceramics. SPS delivers microstructures with good density and fine grain size due to its internal heat generation, high heating rate and short sintering time required. Titanium carbide (TiC) and zirconium diboride (ZrB₂) are selected as the UHTC matrix materials to form composites with different kinds of carbon based materials, including 1D carbon nanotubes (CNTs), 1D chopped carbon fibers, 2D woven and 3D needle-punched carbon fiber fabrics, and 3D graphene networks. One challenge to form the composites by conventional powder processing is the difficulty to achieve a homogeneous mix of ceramic powders and the carbon materials. The aim of this research is to take the advantages of sol-gel processing to synthesize nanostructured carbon reinforced UHTC composites with improved microstructures, mechanical and/or other properties. Graphene/TiC composites were synthesized through sol-gel infiltration of graphene network sponges. The C/Ti ratio of the sol-gel solutions influenced the composition as well as the microstructure of the composites. Graphene sheets could react with titanium dioxide (TiO₂) during the carbothermal reduction, forming a plate-like structure when the carbon content in the sol was low. The samples after SPS sintering showed interesting microstructures of nanostructured TiC surrounded by a network of graphene sheets. The composites were toughened by debonding and bridging of the graphene sheets. It was also proved that the composites exhibited an energy absorption mechanism under impact. CNT/TiC composites were prepared by sol-gel mixing and SPS sintering. The application of sol-gel gave an advantage in homogenous mixing. CNTs were able to toughen the composite by bridging, pullout and crack deflection. The fracture toughness increased with the amount of CNTs, but sacrificing the hardness of the materials. A CNTs containing TiC based sol was coated on ZrB₂ raw powders, forming a homogeneous microstructures after sintering, where most of the TiC grains and CNTs were distributed at the grain boundaries of ZrB₂, forming weak interfaces, which benefited the toughness through crack deflection and impact absorption. The chopped carbon fibers had similar toughening effect to CNTs in the composites. Different types of coatings on the surface of carbon fibers influenced the interface properties between ceramic matrix and fibers, thus affecting the fiber pullout and debonding. Sol-gel infiltration was applied to synthesize ceramic composites with 2D woven and 3D needle-punched carbon fiber fabrics. The results showed that sol-gel infiltration was a much more effective way to uniformly fill the fine pores between fiber filaments than the conventional powder slurry infiltration method. The composites showed improved fracture toughness as a result of fiber pullout, debonding, and crack deflection.

Processing of carbon / ceramic gradient composites by the dipping method

Research on the thermal conductivity and ablation performance of gradient 3D woven carbon/carbon composite

Influence of Coating on the Properties of 3-D Carbon Fiber Braid/Al2O3 Ceramic Composite

Microstructure and mechanical properties of C/C–SiC composites fabricated by a rapid processing method

Preparation and Characterization of Fibrous Alumina and Zirconia Toughened Alumina Ceramics with Gradient Porosity

Improvement of Chemical Liquid Vaporized Infiltration Process for Fast Densification of Carbon/Carbon Composites

Fabrication Of Gradient Porous Beta-Sialon Ceramics Via A Camphene-Based Freeze Casting Process

Fabrication of alumina ceramics with functional gradient structures by digital light processing 3D printing technology

Effect of Chemical Vapour Infiltration Technique on the Gradient Microstructure and High-Temperature Strength of Gel-Cast Al2O3-based Ceramic Moulds

Effects of Carbon Fiber Architecture on the Microstructure and Mechanical Property of C/C-SiC Composites

Study of Rapid Fabrication and Microstructure of C/C-SiC Composites

STUDY OF FABRICATION AND COMPRESSIVE PERFORMANCE OF ALUMINIUM ALLOY MATRIX GRADIENT COMPOSITES REINFORCED WITH SiC PARTICLES

Fabrication and Characterization of Dental Restorative Composites with Gradient Properties

Influence of fabricated process on mechanical properties of porous SiC-particle/ Si3N4 composites

Mechanical and dielectric properties of porous and wave-transparent Si3N4-Si3N4 composite ceramics fabricated by 3D printing combined with chemical vapor infiltration

Study on the Technology and Performance of 3D-Reticulated Porous SiC/Fe Composite Material

Ablation Behavior of Gradient Ceramic-Polymer Composites in Wind Tunnel Environment

Direct ink writing 3D printing of graphene/Al2O3 composite ceramics with gradient mechanics

Processing and mechanical performance of 3D Cf/SiCN composites prepared by polymer impregnation and pyrolysis

Preparation of C/C Composites by Thermal Gradient Chemical Vapor Infiltration with Vaporized Kerosene As a Precursor

Sol-gel synthesis of carbon based materials reinforced ultra high temperature ceramic composites