Abstract:The foamed structure of the central layer, predominantly governed by the addition levels of TiH 2 and the composition of the precursor, in addition to the parameters associated with the foaming process, constitutes the pivotal determinant impacting the spectrum of applications for aluminum foam sandwiches. Systematic research on the foaming behavior of the AlMg 4 Si 8 matrix and pure Al matrix precursors in closed cavities with different TiH 2 addition levels was conducted. The results reveal that with the increasing amount of TiH 2 , specifically at a 200% expansion rate of AlMg 4 Si 8 foams, the number of large pores decreased, the average pore size decreased from 0.67 mm 2 (0.6 wt%) to 0.43 mm 2 (1.0 wt%), and the total number of pores increased from 125 (0.6 wt%) to 156 (1.0 wt%). This trend of pore size consistency was evident not only at the mentioned 200% expansion rate but also across different expansion rates of AlMg 4 Si 8 foams and across all expansion rates of pure Al foams. The pore structures observed in the AlMg 4 Si 8 matrix and pure aluminum matrix foams within a closed cavity exhibited significantly superior characteristics compared to those achieved through free foaming processes. The circularity of pure Al foams was mainly distributed in the range of 1–2, being higher than the AlMg 4 Si 8 foams (1–1.5) due to their low viscosity and foam stability. The compressive curve of AlMg 4 Si 8 foams at a 400% expansion rate reveals that as the average cross-sectional area increased, there was a higher likelihood of experiencing initial collapse conditions. Additionally, the fluctuation of the platform area became more pronounced. Further, the slope corresponding to the elastic stage of the compressive curve increased as the overall stress levels increased.

Effect of TiH2 addition on pore structures of aluminum foam prepared by power metallurgy route

Factors affecting the microstructure of a fine ceramic foam

Optimizing Calcium Addition for Fabricating Aluminum Foams with Different Pore Sizes

Optimization of Cellular Structure of Aluminum Foams Produced by Powder Metallurgy Method

Development of AlMg35-TiH2 composite foaming agent and fabrication of small pore size aluminium foams

Foaming Behavior of AlMg4Si8 Matrix and Pure Al Matrix Precursors in Closed Cavities with Different TiH2 Addition Levels

Effects of process parameters and alloy compositions on the pore structure of foamed aluminum

Fabrication of Aluminum Foams with Small Pore Size by Melt Foaming Method

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Effect of calcium addition on the aluminum alloy A201 foam

Preparation, Characterization and Designing of Porous Ti–6Al–4V Through Metal Injection Molding Without Space Holder

Gas Release Behavior of Cu-TiH2 Composite Powder and Its Application as a Blowing Agent to Fabricate Aluminum Foams with Low Porosity and Small Pore Size

Gas Release Behavior of Cu-TiH 2 Composite Powder and Its Application as a Blowing Agent to Fabricate Aluminum Foams with Low Porosity and Small Pore Size

Effect of Ti content on the cell structure and compressive and energy absorption properties of Al 3 Ti/Al6061 foam composite

Effect of Mg Powder’s Particle Size on Structure and Mechanical Properties of Ti Foam Synthesized by Space Holder Technique

Fabrication of Uniform and Rounded Closed-Cell Aluminum Foams Using Novel Foamable Precursor Particles (FPPs)

Influence of Gas Pressure and Blowing Agent Content on the Formation of Aluminum Alloy Foam

Foaming Process and Properties of 6063 Aluminum Foams by Melt Foaming Method

Microstructure and Compressive Properties of Aluminum Foams Made by 6063 Aluminum Alloy and Pure Aluminum

Coupling Effect Of Porosity And Cell Size On The Deformation Behavior Of Al Alloy Foam Under Quasi-Static Compression