Distributed Feedback Fiber Laser with a Novel Structure

Xiangfei Chen,Dianjie Jiang,Yitang Dai,Haitao Liu

DOI: https://doi.org/10.1109/ofc.2005.192501

2005-01-01

Abstract:A DFB fiber laser with an equivalent phase shift (EPS) is studied and fabricated. A linewidth of 1.5 kHz is experimentally observed in the laser. A single-polarization DFB laser with EPS structure is also obtained.

What problem does this paper attempt to address?

A novel distributed feedback fiber laser based on equivalent phase shift

Dianjie Jiang,Xiangfei Chen,Yitang Dai,Haitao Liu,Shizhong Xie

DOI: https://doi.org/10.1109/LPT.2004.836356

IF: 2.6

2004-01-01

IEEE Photonics Technology Letters

Abstract:A distributed feedback fiber laser employing an equivalent phase shift (EPS) of /spl pi/ is studied theoretically and experimentally for the first time. The EPS is formed through extending one sampling period by 50% in the center of a sampled Bragg grating. An output power of 0.20 mW with sidemode suppression of 67 dB is experimentally observed.
Narrow Linewidth Distributed Feedback Lasers Utilizing Distributed Phase Shift

Yiming Sun,Bocheng Yuan,Xiao Sun,Simeng Zhu,Yizhe Fan,Mohanad Al-Rubaiee,John H. Marsh,Stephen J. Sweeney,Lianping Hou

2024-08-28

Abstract:This study proposes and experimentally demonstrates a distributed feedback (DFB) laser with a distributed phase shift (DPS) region at the center of the DFB cavity. By modeling the field intensity distribution in the cavity and the output spectrum, the DPS region length and phase shift values have been optimized. Experimental comparisons with lasers using traditional {\pi}-phase shifts confirm that DFB lasers with optimized DPS lengths and larger phase shifts (up to 15{\pi}) achieve stable single longitudinal mode operation over a broader current range, with lower threshold current, higher power slope efficiency, and a higher side mode suppression ratio (SMSR). Furthermore, the minimum optical linewidth is reduced significantly, from 1.3 MHz to 220 kHz.

Optics
Phase-matched Combined Distributed-Feedback/fabry-pérot Structure for Semiconductor Lasers

J HE,M CADA

DOI: https://doi.org/10.1016/0030-4018(94)90181-3

IF: 2.4

1994-01-01

Optics Communications

Abstract:A phased-matched combined distributed-feedback/Fabry-Pérot (DFB/FP) structure is proposed for semiconductor lasers, particularly for the surface-emitting type. The conditions for constructive resonances of the DFB and the FP sections are established. We demonstrate that the DFB/FP structure can have a much stronger resonance and consequently a lower threshold than simple DFB or FP structures with a comparable cavity length. It is also found that a lower threshold can be obtained if the laser wavelength is below the stop band of the DFB region, due to partial gain coupling in the structure.
Dual-wavelength DFB Fiber Laser Based on a Chirped Structure and the Equivalent Phase Shift Method

Yitang Dai,Xiangfei Chen,Jie Sun,Yu Yao,Sigang Yang,Ming Xin,Lina He,Shizhong Xie

DOI: https://doi.org/10.1109/lpt.2006.882282

2006-01-01

Abstract:A chirped phase-shifted structure is demonstrated for compact multiwavelength distributed feedback (DFB) fiber laser at room temperature for the first time. The chirped structure provides separated resonance cavities and then the stable multiwavelength operation. The equivalent phase shift method is demonstrated to realize the desired chirp and phase shifts simply and flexibly. A 44-pm-spaced dual-wavelength DFB fiber laser is then achieved experimentally, which is the narrowest spacing ever reported for a compact multiwavelength fiber laser
An Experimental Research about Dye-Doped Distributed Feedback Laser

Zhigang Zhou,Rongwei Fan,Zhaodong Chen,Xinrui Xu,Deying Chen

DOI: https://doi.org/10.1117/12.2246852

2016-01-01

Abstract:Dye-doped distributed feedback (DFB) structure is an essential structure for DFB laser. This paper presents an operative method to design a kind of dye-doped distributed feedback laser based on dye-doped holographic polymer dispersed liquid crystal (HPDLC) matrix. The results show that we have processed DFB structure of 10μm period, with a relatively low period deviation of less than 1%. Furthermore, we gain output characteristics of DFB structure through experimental methods, which show good characteristics for wide tuning range, narrow linewidth laser output production.
Two-wavelength fiber laser based on two equivalent phase shifts

Zuowei Yin,Xinghua Tu,Shengchun Liu,Lei Zhang,Yan-qing Lu,Xiangfei Chen

DOI: https://doi.org/10.1117/12.821057

2008-01-01

Abstract:A two-wavelength fiber laser with two π-equivalent phase shifts (EPSs) is studied and fabricated. The π-EPS is obtained through extending one sampling period by 50% in a fiber sampled Bragg grating (SBG). To get a two-wavelength fiber laser lasing in the -1st channel, two π-EPSs are introduced in the position of L/3 and 2L/3 in the SBG, where L is the total length of the SBG. A stable 22-pm-spaced dual wavelength DFB fiber laser is achieved in the experiment.
Dual-Wavelength DFB Fiber Laser Based on Unequalized Phase Shifts

Jie Sun,Yitang Dai,Yejin Zhang,Xiangfei Chen,Shizhong Xie

DOI: https://doi.org/10.1109/lpt.2006.887222

IF: 2.6

2006-01-01

IEEE Photonics Technology Letters

Abstract:A novel structure for dual-wavelength distributed feedback (DFB) fiber laser is proposed and experimentally demonstrated. This structure is based on a uniform fiber Bragg grating with two unequalized phase shifts, which markedly suppress the mode competition of the two lasing wavelengths; and then a 52-pm-spaced dual-wavelength DFB fiber laser operating at single-longitudinal-mode and single-polarization is achieved at room temperature. A simple method is also implemented to fabricate the phase shifts with high precision
Experiment of Distributed Feedback Dye Laser

ZHANG Yong-sheng,YAN Li-xin,HUANG Ke,LIU Jing-ru

DOI: https://doi.org/10.3969/j.issn.1007-2276.2005.02.007

2005-01-01

Abstract:Analysis on the working principle of a distributed feedback dye laser with sub-pico-second output(0.5 ps) is carried out, and the experimental results are obtained. It is pointed out that a simple change of the system will realize pulse width tunable.Additionally, a simple adjust method is described to obtain single mode DFDL laser output.
Numerical Analyzation of Distributed Feedback Lasers with Different Phase Shift Structures

Bo Wang,Peiqi Zhou,Xingjun Wang

DOI: https://doi.org/10.1364/acpc.2021.t4a.158

2021-01-01

Abstract:We optimize phase shift structures of distributed feedback (DFB) lasers. For the multi-distributed phase shift laser, the output slope can reach up to 51.90% when the optimal cavity length is 2.2 mm.
Study of Cascaded Tunable DFB Semiconductor Laser with Wide Tuning Range and High Single Mode Yield Based on Equivalent Phase Shift Technique

Lianyan Li,Song Tang,Jun Lu,Yuechun Shi,Baoli Cao,Xiangfei Chen

DOI: https://doi.org/10.1016/j.optcom.2015.04.077

IF: 2.4

2015-01-01

Optics Communications

Abstract:The tunable distributed feedback (DFB) semiconductor lasers with cascaded configuration were designed and fabricated using equivalent phase shift (EPS) technique. 32-wavelength division multiplexing (WDM) channels with 50-GHz and 100-GHz wavelength spacing were experimentally demonstrated. In such a tunable laser, single mode operation can be ensured by introducing EPS and the wavelength tuning can be realized by cascaded sections with specific sampling periods combining with chip heating. The proposed approach has some advantages such as good single mode property, low fabrication cost and feasibility of monolithic integration. The experimental results show that the tuning range can be nearly up to 25nm and the side mode suppression ratios (SMSRs) of most channels are above 40dB. The proposed laser should be promising for cost-effective applications in WDM systems.
Linewidth Compression of DFB Laser with a High Ratio Based on SIL and PDH

Ling Yang,Bing Wei,Hanfeng Xu,Ziyue Wang,Xiaofeng Jin

DOI: https://doi.org/10.1109/lpt.2023.3335215

IF: 2.6

2024-01-01

IEEE Photonics Technology Letters

Abstract:A cost-effective linewidth compressing method for distributed feedback (DFB) laser with a high ratio based on self-injection locking (SIL) and Pound-Drever-Hall (PDH) is proposed. The combination of SIL and PDH helps to reduce the phase noise of the DFB laser, thus a high linewidth compression ratio can be achieved. The experiment results show the single sideband (SSB) phase noise of a commercial DFB laser has been reduced by more than 75-dB in the frequency range from 100-Hz to 10-kHz. The linewidth is narrowed to be around 140-Hz compared with the free-running state of 2.3-MHz, with a high compression ratio of over 1.6 x 10(4). The in-loop Allan deviation (ADEV) of the DFB laser is measured to be 5.4 x 10(-11) within the average time of 100 s, indicating the long-term frequency stability.
Stable Multi-Wavelength Erbium-Doped Fiber Laser by Using Dispersion-Shifted Fiber

Ying Gao,Daru Chen,Shiming Gao

DOI: https://doi.org/10.1109/cleopr.2007.4391316

2007-01-01

Abstract:A multi-wavelength erbium-doped fiber laser with a simple line-structure is achieved by employing a Sagnac interferometer. It is demonstrated to be quite stable at room temperature due to the four-wave mixing effect in the dispersion-shifted fiber inserted in the laser cavity.
Distributed feedback fiber laser based on a fiber Bragg grating inscribed using the femtosecond point-by-point technique

M I Skvortsov,A A Wolf,A V Dostovalov,A A Vlasov,V A Akulov,S A Babin

DOI: https://doi.org/10.1088/1612-202x/aa9cca

IF: 1.704

2018-02-05

Laser Physics Letters

Abstract:A distributed feedback (DFB) fiber laser based on a 32-mm long pi-phase-shifted fiber Bragg grating inscribed using the femtosecond point-by-point technique in a single-mode erbium-doped optical fiber (CorActive EDF-L 1500) is demonstrated. The lasing power of the DFB laser reaches 0.7 mW at a wavelength of 1550 nm when pumped with a laser diode at a wavelength of 976 nm and power of 525 mW. The width of the lasing spectrum is 17 kHz. It is shown that the pi-phase-shifted fiber Bragg grating fs-inscribed in a non-PM fiber provides the selection of the single polarization mode of the DFB laser. DFB laser formation in a highly doped non-photosensitive optical fiber (CoreActive SCF-ER60-8/125-12) is also demonstrated.

optics,physics, applied
A Novel Single-Mode, Linearly Polarized, Erbium-Doped Fiber Laser with a Stabilized Frequency.

Yuanyue Guo,Dongjin Wang,Falin Liu,Naoto Kishi

DOI: https://doi.org/10.1109/cits.2013.6705730

2013-01-01

Abstract:We report on an experimental study of a stabilized single-mode, linearly polarized, erbium-doped fiber laser with an unique structure of double-cavities. In its linear cavity, the effect of spatial-hole burning (SHB) is eliminated to prevent multi-longitudinal-mode oscillation by using 45° Faraday rotator mirror, meanwhile, in its another polarization maintaining ring cavity, the effect of SHB induced by a stable external light and the lasing light is enhanced efficiently to suppress the mode-hopping by the polarization state control method. Consequently, a single-mode, linearly polarized operation is demonstrated with the lasing frequency shift of less than 20MHz, its linewidth less than 3.5 kHz and the degree of polarization of 99. 9%.
Line-Width Compression Of The Distributed Feedback Laser With An External Parallel Feedback Cavity

Wang Zi-Nan,Wang Cui-Yun,Wang Da-Liang,Lu Ping,Yu Xiao-Qi,Xu Lian-Yu,Yang Yi,Jiang Yun,Zhu Li-Xin,Li Zheng-Bin

DOI: https://doi.org/10.1117/12.900983

2011-01-01

Abstract:The distributed feedback laser (DFB) is a typical laser diode where the active region of the device is periodically structured as a diffraction grating. The output of a DFB laser has one single longitudinal mode and a relatively narrow line-width, usually several megahertz or one order less. However, applications such as coherent optical communication and accurate fiber sensing demand an even narrower line-width. An effective method for compressing a DFB laser is demonstrated. The line-width of a DFB laser, 200 KHz detected originally, is suppressed to sub kilohertz by adding an external parallel feedback cavity. The DFB laser is normatively designed but without the output isolator. The parallel feedback cavity is constructed by inserting several pieces of multimode fiber into a standard linear single-mode fiber cavity. In multimode fiber, each transverse mode has a different propagation constant. Equivalently, when a light beam propagates from single mode fiber to multimode fiber, it will split into a few parallel light paths with different propagation constants. The external cavity and DFB cavity form a compound resonant cavity for light beams. Lasing light in the compound cavity must fit the restrictions of all light paths, thus line-width of the final output is suppressed. When a passive external cavity is used, the line-width is suppressed to 1.25 KHz, detected by a delayed self-heterodyne interferometer with a 100km fiber delay line. By adding an erbium doped fiber amplifier (EDFA) into the external cavity for loss compensation, the result is updated to 430 Hz. This line-width suppressing method can be applied for other types of fiber lasers in a similar way. The parallel feedback mechanism is also suggested for general laser cavity designing to achieve ultra narrow line-width light source.
Dual-wavelength fibre laser with a novel distributed feedback structure and its application in microwave generation

Jie Sun,Yitang Dai,Xiangfei Chen,Hongwei Chen,Yejin Zhang,Shizhong Xie

DOI: https://doi.org/10.1109/ECOC.2006.4800963

2006-01-01

Abstract:We present a novel distributed feedback structure for a stable dual-wavelength fibre laser with a frequency interval of 40GHz; and the generated microwave signal has a linewidth <10kHz without any feedback.
Single-frequency Yb-doped Fiber Laser with Distributed Feedback Based on a Random FBG

Zhinan Zhang,Jiawei Shi,Jihuang Zhang,Lulu Wang,Xinyong Dong,Perry Ping Shum,Xueyuan Du,Hanwei Zhang,Pengfei Ma,Anthony Wong,Da Chen,Hongjun Wang,Liangying Wu,Li Pei,Jianshuai Wang

2016-01-01

Abstract:Single-frequency operation of a 1.03 μm fiber laser with random distributed feedback (RDFB) is demonstrated. The laser cavity is based on a 4 cm long fiber Bragg grating (FBG) consisting of 10 homogeneous subgratings with random phase and amplitude of refractive index modulation inscribed in a polarization maintaining (PM) Yb-doped fiber. Such RDFB laser generates single longitudinal mode with output power up to 25 mW, which is 3.5 times higher than that for a DFB laser based on regular π-shifted FBG of the same length in the same fiber. The single-frequency linewidth is measured to be <100 kHz in both cases. The observed difference of the DFB and RDFB lasers is confirmed by numerical simulation showing different longitudinal distribution of intra-cavity radiation in these cases, analogous to those in the experiment.
Tunable narrow linewidth DFB laser diode with artificially enhanced Rayleigh scattering-based external distributed feedback

Jiali Li,Da Wei,Leilei Shi,Liyang Jin,Lei Zhai,Shumin Yang,Minzhi Xu,Yujia Li,Ligang Huang,Tao Zhu

DOI: https://doi.org/10.1364/oe.534601

IF: 3.8

2024-11-25

Optics Express

Abstract:Jiali Li, Da Wei, Leilei Shi, Liyang Jin, Lei Zhai, Shumin Yang, Minzhi Xu, Yujia Li, Ligang Huang, Tao Zhu We experimentally demonstrate a tunable narrow-linewidth distributed feedback (DFB) laser diode based on the artificially enhanced Rayleigh ... [Opt. Express 32, 43771-43777 (2024)]

optics
Self-Aligned Emission of Distributed Feedback Lasers on Optical Fiber Sidewall

Tianrui Zhai,Xiaojie Ma,Liang Han,Shuai Zhang,Kun Ge,Yanan Xu,Zhiyang Xu,Libin Cui

DOI: https://doi.org/10.3390/nano11092381

IF: 5.3

2021-09-13

Nanomaterials

Abstract:This article assembles a distributed feedback (DFB) cavity on the sidewalls of the optical fiber by using very simple fabrication techniques including two-beam interference lithography and dip-coating. The DFB laser structure comprises graduated gratings on the optical fiber sidewalls which are covered with a layer of colloidal quantum dots. Directional DFB lasing is observed from the fiber facet due to the coupling effect between the grating and the optical fiber. The directional lasing from the optical fiber facet exhibits a small solid divergence angle as compared to the conventional laser. It can be attributed to the two-dimensional light confinement in the fiber waveguide. An analytical approach based on the Bragg condition and the coupled-wave theory was developed to explain the characteristics of the laser device. The intensity of the output coupled laser is tuned by the coupling coefficient, which is determined by the angle between the grating vector and the fiber axis. These results afford opportunities to integrate different DFB lasers on the same optical fiber sidewall, achieving multi-wavelength self-aligned DFB lasers for a directional emission. The proposed technique may provide an alternative to integrating DFB lasers for applications in networking, optical sensing, and power delivery.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology,chemistry
Dual-Wavelength Er-Doped Fiber Laser Based on Phase Sampled Fiber Bragg Grating

Heng Ji,Sigang Yang,Ye Zhang,Shizhong Xie

DOI: https://doi.org/10.3788/aos20082805.0919

2008-01-01

Abstract:A dual-wavelength distributed feedback (DFB) fiber laser based on phase sampling is proposed and demonstrated. Change of phase and sampling period is introduced at different positions along a sampling Bragg grating. It is demonstrated theoretically that this structure can provide separate resonant cavities to overcome mode competition caused by gain homogeneous broading. A 0.46 nm-spaced dual-wavelength DFB fiber laser is achieved on an Er-doped fiber with exciter laser and homogeneous phase plate. Experiments shows that dual-wavelength lasing is achieved and laser power is in reverse proportion with coupling coefficient of the FBG.

Distributed Feedback Fiber Laser with a Novel Structure

A novel distributed feedback fiber laser based on equivalent phase shift

Narrow Linewidth Distributed Feedback Lasers Utilizing Distributed Phase Shift

Phase-matched Combined Distributed-Feedback/fabry-pérot Structure for Semiconductor Lasers

Dual-wavelength DFB Fiber Laser Based on a Chirped Structure and the Equivalent Phase Shift Method

An Experimental Research about Dye-Doped Distributed Feedback Laser

Two-wavelength fiber laser based on two equivalent phase shifts

Dual-Wavelength DFB Fiber Laser Based on Unequalized Phase Shifts

Experiment of Distributed Feedback Dye Laser

Numerical Analyzation of Distributed Feedback Lasers with Different Phase Shift Structures

Study of Cascaded Tunable DFB Semiconductor Laser with Wide Tuning Range and High Single Mode Yield Based on Equivalent Phase Shift Technique

Linewidth Compression of DFB Laser with a High Ratio Based on SIL and PDH

Stable Multi-Wavelength Erbium-Doped Fiber Laser by Using Dispersion-Shifted Fiber

Distributed feedback fiber laser based on a fiber Bragg grating inscribed using the femtosecond point-by-point technique

A Novel Single-Mode, Linearly Polarized, Erbium-Doped Fiber Laser with a Stabilized Frequency.

Line-Width Compression Of The Distributed Feedback Laser With An External Parallel Feedback Cavity

Dual-wavelength fibre laser with a novel distributed feedback structure and its application in microwave generation

Single-frequency Yb-doped Fiber Laser with Distributed Feedback Based on a Random FBG

Tunable narrow linewidth DFB laser diode with artificially enhanced Rayleigh scattering-based external distributed feedback

Self-Aligned Emission of Distributed Feedback Lasers on Optical Fiber Sidewall

Dual-Wavelength Er-Doped Fiber Laser Based on Phase Sampled Fiber Bragg Grating