Abstract:The thickness of steel plates used in the member has gradually increased to meet the load-bearing capacity requirements of long-span steel bridges. As the primary connection method of thick steel plate, welding will result in considerable welding residual stress with complex distribution. Large welding residual stress will significantly impact the performance of steel bridges. In this paper, the distribution of residual stress in welded thick steel plate is systematically studied, a specimen with a thickness of 80 mm was designed and fabricated, and the welding residual stress was measured by X-ray diffraction. The finite element model was established and verified by test results. Subsequently, the finite element calculation of the welding residual stress of steel plates with thicknesses of 20, 40, 60, 80, and 100 mm was carried out, and the distribution of surface residual stress and the influence of plate thickness on residual surface stress were studied; then the spatial evolution mechanism of welding residual stress was studied, and the distribution of residual stress inside steel plate and the influence of plate thickness on the distribution of residual stress were revealed. The results show that the surface and internal residual stresses of 20–100 mm thick plates have good symmetry on the paths perpendicular to the weld seam, and asymmetry only occurs in the weld seam and heat-affected zone where the stress fluctuates. On the paths perpendicular to the weld seam, the stress in the X direction transitions from the "M" shape distribution on the surface to the "Π" shape distribution inside for 20–40 mm thick plates, and the residual stress near the weld seam gradually changes from compressive to tensile; The distribution of stress in the X direction in the 80–100 mm thick plate has experienced the transition from "M" shape to "Π" shape to "M" shape, and the stress near the weld seam has experienced the transition from compressive to tensile to compressive. The stress change in the X direction of the 60 mm thick plate is between the above two cases. On the path of internal stress along the thickness, the maximum stress in the X direction is 310–400 MPa for 20–40 mm thick plates, which appears at about 1/2 plate thickness. The maximum stress in the X direction for 60–100 mm thick plates is 400–480 MPa, which appears at 0.2–0.3 times the thickness of the plate from the upper surface. The results could serve as a reference for welding residual stress analysis and guide optimization design of steel bridges made of thick steel plate.

Planeness of upper ring surface of nether frame carbody of grab

Simulation and prediction for welding deformation on welding procedure of hand pallet truck

Numerical Prediction and Control of Deformation and Residual Stress in Double-Sided Arc Welding of Large Pressure Hull

Research of Position Accuracy of Welding Grab's Nether Frame Carbody

Reverse Deformation Design for Bending Control in Welding of Ring Stiffeners

Prediction of Welding Deformation of Underframe

Prediction for Welding Deformation Reducing by Welding Sequence Optimization of Upper Plate

Effect of Welding Residual Stress on Plastic Buckling of Axially Compressed Cylindrical Shells with Patterned Welds

Prediction and Controlling for Welding Deformation of Propeller Base Structure

Prediction of deformation of large welding fabrication based on inherent strain

Study of vertical mechanical constraint on welding deformation and residual stress of a deck grillage

Experimental research and numerical analysis of welding residual stress of butt welded joint of thick steel plate

Effect of groove angle on the residual stress and deformation of nuclear waste container cylinder body welded by plasma arc weldingAuswirkung des Nutwinkels auf die Eigenspannung und die Verformung des Zylinderkörpers eines plasmageschweißten Atommüllbehälters

Prediction of Surface Wrinkle Defect of Welding Wire Steel ER70S-6 in Hot Bar Rolling Process Using Finite Element Method and Experiments

A Comparative Study of the Residual Deformation of an Automotive Gear-Case Assembly Due to Deep-Penetration High-Energy Welding

Deformation prediction of locomotive coping welding structure based on inherent strain

Prediction of welding distortion during assembly process of thin plate structures

Numerical Prediction of Welding Distortion Considering Gravity Force on General Ship Grillage Structure by Elastic Finite Element Method Using Inherent Strain

Research on welding deformation for box girder of bridge crane based on thermal elasto-plastic theory

Welding deformation prediction of hull structure based on Weld-sta software

Numerical Investigation on Evolution of Plastic Zone During Inertia Friction Welding Process of Ring Parts