Abstract:Recently, high-temperature composites reinforced with in-situ phases have been developed as a new class of composites for harsh environments. The behaviour of these composites under sudden heating and cooling conditions is greatly influenced by the type and fraction of components. The aim of this study is to investigate the microstructural properties and mechanical response of iron based composites after thermal shock cycling. The fabrication process involved in-situ powder metallurgy (IPM) sintering of Fe–B4C starting powders. The samples were subjected to thermal shock with a constant temperature differences (ΔT: 600 °C) and varied cycles (N: 1–50). Comparison of microstructural changes and mechanical behaviour before and after thermal shock has been carried out. The boron atoms released from the initial B4C generated diffusion zones in the matrix dominated by iron boride phases (Fe2B/FeB). An effective matrix-reinforcement interface has been created by in-situ powder metallurgy, where boride phases are almost homogeneously distributed in the iron matrix. While the hardness of the composites was significantly developed by the Fe2B/FeB phases, the addition of B4C resulted in a reduction in the coefficient of thermal expansion (CTE). The in-situ phases contributed in the minimisation of the coefficient mismatch by balancing the thermal expansion coefficients between iron and the initial B4C. Under the influence of thermal shock, microcracks and then macrocracks formed on the sample surfaces, increasing in width and depth with thermal cycles. This resulted in accelerated fracture damage under post-thermal loading. Both the impact and flexural strengths of the samples were significantly reduced as the number of thermal cycles increased. Although the 20% B4C reinforced composite provided maximum hardness, it showed poor resistance to thermal loading. The best results for mechanical loads were achieved by the 5% B4C reinforced composite, which showed no cracks even after 50 thermal cycling.

Thermal Shock Behaviour of Alumina-Iron Composites

Resistance of alumina-copper composite to thermal shock

The thermal shock behavior of alumina-copper composite

Damage-tolerant Laminated Composites in Thermal Shock

Influence of Tungsten Carbide Particles on Resistance of Alumina Matrix Ceramics to Thermal Shock

Study on Thermal Shock Resistance of Alumina Composite Ceramics by Indention Quenching Method

Design and characterization of therm-al shock resistance of several typical zirconia reinforced alumina ceramic composites

Thermal durability of aluminum titanate-mullite composites with high thermal shock resistance

Thermal Shock Behaviors of AlN / BN Laminated Ceramic Composites

Thermal Shock Resistance for Wisker and Particle Toughing Al2O3 Ceramic Matrix Composites

A Novel Design to Produce High-Strength and High-Toughness Alumina Self-Lubricated Composites with Enhanced Thermal-Shock Resistance-Part I: Mechanical Properties and Thermal Shock Behavior of Al2o3/Mo-Al2o3 Laminated Composites

Enhanced thermal shock response of Al 2 O 3 –graphite composites through a layered architectural design

High temperature thermo-physical properties and thermal shock behavior of metal–diborides-based composites

Thermal shock effects on the microstructure and mechanical properties of iron-based composites reinforced by in-situ Fe2B/FeB ceramic phases

Influence of Thermal Shock Damage on the Flexure Strength of Alumina Ceramic at Different Temperatures

High Temperature Tensile Properties of Al2O3/Cu Composite

Enhanced thermal shock resistance of ZrO2-reinforced Al2O3–CaAl12O19 composites prepared from ferrotitanium slag: Crack propagation resistance mechanisms

The Influence of Surface Heat Transfer Conditions on Thermal Shock Behavior of ZrB2–SiC–AlN Ceramic Composites

High strength and high fracture toughness ceramic−iron aluminide (Fe3Al) composites

Effect of Thermal Mismatch Stress on Thermal Expansion Behaviors of Al<sub>18</sub>B<sub>4</sub>O<sub>33</sub>w/Al Composite Containing Fe<sub>3</sub>O<sub>4</sub> Particle