Abstract:Recently, high-temperature composites reinforced with in-situ phases have been developed as a new class of composites for harsh environments. The behaviour of these composites under sudden heating and cooling conditions is greatly influenced by the type and fraction of components. The aim of this study is to investigate the microstructural properties and mechanical response of iron based composites after thermal shock cycling. The fabrication process involved in-situ powder metallurgy (IPM) sintering of Fe–B4C starting powders. The samples were subjected to thermal shock with a constant temperature differences (ΔT: 600 °C) and varied cycles (N: 1–50). Comparison of microstructural changes and mechanical behaviour before and after thermal shock has been carried out. The boron atoms released from the initial B4C generated diffusion zones in the matrix dominated by iron boride phases (Fe2B/FeB). An effective matrix-reinforcement interface has been created by in-situ powder metallurgy, where boride phases are almost homogeneously distributed in the iron matrix. While the hardness of the composites was significantly developed by the Fe2B/FeB phases, the addition of B4C resulted in a reduction in the coefficient of thermal expansion (CTE). The in-situ phases contributed in the minimisation of the coefficient mismatch by balancing the thermal expansion coefficients between iron and the initial B4C. Under the influence of thermal shock, microcracks and then macrocracks formed on the sample surfaces, increasing in width and depth with thermal cycles. This resulted in accelerated fracture damage under post-thermal loading. Both the impact and flexural strengths of the samples were significantly reduced as the number of thermal cycles increased. Although the 20% B4C reinforced composite provided maximum hardness, it showed poor resistance to thermal loading. The best results for mechanical loads were achieved by the 5% B4C reinforced composite, which showed no cracks even after 50 thermal cycling.

High temperature thermo-physical properties and thermal shock behavior of metal–diborides-based composites

High pressure sintering behavior and mechanical properties of cBN-Ti 3Al and cBN-Ti 3Al-Al composite materials

Enhanced thermal shock resistance of BN-based composites sintered by hot-pressing with the introduction of nano oxides

High Temperature Tensile Properties of in Situ TiBw/Ti6Al4V Composites with a Novel Network Reinforcement Architecture

Cyclic thermal shock resistance of h-BN composite ceramics with La2O3–Al2O3–SiO2 addition

Microstructure, mechanical properties and thermal shock behavior of h-BN-SiC ceramic composites prepared by spark plasma sintering

Interfacial Bonding of Al-Si/C Composites and Improvement of the Thermal Shock Resistance

Microstructure and Mechanical Properties of Al–B 4 C Composite at Elevated Temperature Strengthened with in Situ Al 2 O 3 Network

Thermal Shock Resistance of in Situ Formed Si2N2O–Si3N4 Composites by Gelcasting

Influence of Tungsten Carbide Particles on Resistance of Alumina Matrix Ceramics to Thermal Shock

Microstructure evolution and tensile behavior of MgAlB4w/Al composites at high temperatures

Effect of Al content on impact resistance behavior of Al-Ti-B4C composite fabricated under air atmosphere

High temperature tribological behavior of Mo–12Si–8.5B alloy reinforced with MoAlB ceramic

Hardness and toughness improvement of SiC‐based ceramics with the addition of (Hf 0.2 Mo 0.2 Ta 0.2 Nb 0.2 Ti 0.2 )B 2

Enhanced high temperature mechanical properties and heat resistance of an Al–Cu–Mg–Fe–Ni matrix composite reinforced with in-situ TiB2 particles

Crossover of thermal conductivity in SiC-reinforced ZrB2–HfB2 composites at elevated temperatures

Thermal shock effects on the microstructure and mechanical properties of iron-based composites reinforced by in-situ Fe2B/FeB ceramic phases

Effect of Thermal Exposure on the Interface Microstructure and Interfacial Shear Strength of the SiC Fiber Reinforced AlFe5Si2 Matrix Composite

Effect of thermal shock induced dislocation multiplication on the thermal conductivity of 60 vol% SiCp/Al–7Si composites

Mechanical properties and thermal shock resistance of TiB2‒B4C composite ceramic tool materials at microscopic scale