Abstract:High-silicon and molybdenum (SiMo) ductile iron is a common heat-resistant alloy that may be exposed to high-temperature wear during service in many of its applications. The wear behavior of four SiMo ductile iron alloys was evaluated at different temperatures up to 750 °C. This research focuses on the influence of various Mo contents on the microstructure, structural stability, and hence, the wear performance of such alloys. Thermodynamic calculations proposed the phase diagrams, critical transformation temperatures, and phase volume fractions in all samples by means of Thermo-Calc software. The dilatometry measurements were carried for confirming the theoretical results of Thermo-Calc thermodynamic calculations. The results revealed that the microstructure of SiMo ductile cast iron consists of nodular graphite and a ferrite matrix with carbides embedded in the fine precipitates at the grain boundary regions. The type of carbides and the nature of these fine precipitates are discussed according to EDX and SEM results. Adding molybdenum enhanced the wear performance of SiMo by decreasing the weight loss by about 40–70% compared to a Mo-free alloy. This is due to the increased molybdenum carbides, which increase hardness and improve wear resistance in SiMo alloys. The high temperatures have a negative effect on reducing the wear resistance at 250 °C. On the other hand, the wear resistance unexpectedly started to increase at higher temperatures of 500 °C and 750 °C because of the contribution of oxidative wear with abrasive wear by forming a protective oxide layer. Furthermore, the obtained results supported the idea that adding molybdenum improves wear resistance at high temperatures. Hence, SiMo has the potential to be wear-resistant material in wider applications requiring high-temperature wear resistance.

High temperature tribological behavior of Mo–12Si–8.5B alloy reinforced with MoAlB ceramic

High temperature tribological behaviors of MoAlB ceramic from 800 to 1200°C

Formation and Oxidation Behavior of Mo-Si-B Composite Coatings with B-rich Interlayer Prepared by Slurry Sintering Method

Influence of Al and Mo on microstructure and tribological behaviors of Co-based superalloy

High temperature tribological behaviors and wear mechanisms of NiAl-MoO3/CuO composite coatings

Influence of Mo doping on the tribological behavior of Ti3AlC2 ceramic at different temperatures

Tribological behaviors of MoAlB ceramic in artificial seawater

High Temperature Wear Behavior of Nial-Cr(Mo)-Ho-Hf Eutectic Alloy

High-Temperature Rheological Behavior and Microstructure Evolution of Mo-12Si-8.5B Alloy Reinforced by Layered Mo2TiAlC2 Phase

Preparation, microstructure and mechanical properties of MoAlB-0.15% Si ceramics with superior strength and toughness

Preparation of fine-grained MoAlB with preferable mechanical properties and oxidation resistance

Synthesis and properties of MoAlB composites reinforced with SiC particles

Tribological behavior of h -BN/Al 2 O 3 self-lubricating composites in extreme environments–Part I: Lubricating behavior and ultra-low friction coefficient mechanism in air environments from room temperature to 1200 °C

The tribological behavior of hybrid aluminum alloy nanocomposites at High temperature: Role of nanoparticles

The Effect of MoAlB Substitutions on the Oxidation Behavior of ZrB2-SiC Composites at 1600°C

Wear Properties of NiAl Based Materials

Preparation and anisotropic tribological properties of MoAlB/Al laminated composites

Effect of Molybdenum Contents on Microstructure and High-Temperature Wear Behavior of SiMo Ductile Iron

Investigation of the elevated temperature tribological property and wear mechanism of Fe‐15Cu‐0.8C materials containing Mo‐coated MoS2 powders

Improving high-temperature wear resistance of arc-evaporated AlCrN coatings by Mo alloying

High-Temperature Friction and Wear Behavior of Nickel-Alloy Matrix Composites with the Addition of Molybdate