Abstract:High entropy alloy nitride coatings (HEAN), showing superior mechanical strength, high oxidation resistance, and thermal stability, have often been used in protective hard coatings field. However, the high temperature tribological field of novel HEA nitride films has not yet been well studied. The correlations among tribological properties, compressive residual stress, mechanical properties, and self-lubricating oxide are still limited.In this research, the novel (AlCrNbSiTiMo)N coatings were fabricated on both Inconel-718 and Si (100) substrate by radio frequency (RF) magnetron sputtering via tuning both substrate bias at 300 °C deposition temperature. The (AlCrNbSiTiMo)N coatings with a specific substrate bias exhibit an outstanding hardness of 34.5±0.8 GPa.In the wear test at 700 °C, the films deposited at −100 V revealed the lowest wear rate around 1.2 × 10−6 mm3N−1 m−1. With Molybdenum doping, the MoO3 Magnéli phase was observed on the surface at elevated temperature wearing process, and the friction coefficient at high temperature decreased significantly due to a lubricating surface. The coating exhibited the average friction coefficient value of 0.48 in the wear test of 700 °C. The high temperature tribological performance was addressed and related to the mechanical properties, the plastic deformation resistance H3/E2, and the excess residual stress of the films.This study provides a new design for hard coatings applied to severe wearing conditions. By tuning substrate bias, the (AlCrNbSiTiMo)N coatings exhibit outstanding mechanical and tribological characteristics, which will be a promising candidate for high temperature tribological protective film.

Improving high-temperature wear resistance of arc-evaporated AlCrN coatings by Mo alloying

Comparative study on mechanical and tribological properties of Cr–Al–N and Cr–Al–O coatings deposited by cathodic arc evaporation

Structural, Mechanical and Thermal Properties of CrAlNbN Coatings

Influence of Mo contents on the tribological properties of CrMoN/MoS2 coatings at 25–700 °C

Effect of Mo addition on microstructure and wear resistance of laser clad AlCoCrFeNi-TiC composite coatings

Evolution in microstructure, wear, corrosion, and tribocorrosion behavior of Mo-containing high-entropy alloy coatings fabricated by laser cladding

High Temperature Oxidation and Tribological Behavior of Cr3C2-25CoNiCrAlY and Cr3C2-25NiCr Coatings Prepared by AC-HVAF

Improvement of Tribological Performance of TiAlNbN Hard Coatings by Adding AlCrN

High-temperature Tribological Properties of a Novel AlFeCoNiCr-Cr3C2 Cermet Coatings

Influence of Al and Mo on microstructure and tribological behaviors of Co-based superalloy

Thermostability, oxidation, and high-temperature tribological properties of nano-multilayered AlCrSiN/VN coatings

The Microstructures and Wear Resistance of CoCrFeNi2Mox High-Entropy Alloy Coatings

Improvement of High Temperature Wear Behavior of In-Situ Cr3C2-20 Wt. % Ni Cermet by Adding Mo

Effect of Aluminum Content on the Tribological Properties of AlxCrTiMo Refractory High-Entropy Alloys

The Synergistic Effects Of Mo As An Alloy Element Added To Chromium Carbide Coatings On Their Lubrication Properties At High-Temperatures

Effect of Mo on Microstructure and Oxidation of NiCoCrAlY Coatings on High Nb Containing TiAl Alloys

Microstructure and Wear Resistance Property of AlFeCrNiMox Coatings by Plasma Cladding

Influence of TiN and ZrN Insertion Layers on the Microstructure, Mechanical and Thermal Properties of Cr–Al–N Coatings

Improvement of high entropy alloy nitride coatings (AlCrNbSiTiMo)N on mechanical and high temperature tribological properties by tuning substrate bias

Influence of Interlayer Materials on the Mechanical Properties and Thermal Stability of a CrAlN Coating on a Tungsten Carbide Substrate

Microstructure Evolution and Enhanced Wear Resistance of Al2CrFeNiMo High Entropy Alloy Coating Fabricated by Laser Cladding