Abstract:Purpose The purpose of this paper is to optimise the electro‐discharge machining (EDM) parameters and investigate feasibility of using direct metal laser sintering (DMLS) parts as EDM electrodes. Design/methodology/approach In this paper the effects of discharge current, pulse‐on‐time, flushing pressure are optimized for minimum tool wear rate (TWR), maximum metal removal rate (MRR) and minimum surface roughness (Ra). Taguchi‐based L 9 orthogonal array has been used for performing experiments on EDM machining of EN 24 steel using DMLS electrodes. The grey relational analysis combined with ANOVA techniques have been employed to determine the optimal level as well as their significance. Findings Experimental results have shown that the performance characteristics of the EDM process (TWR, MRR and surface roughness) using DMLS electrode can be quantified and controlled effectively by grey relational approach presented in the study. Current is found to be the most affective parameter in EDM machining using DMLS electrode. Excessive DMLS tool (electrode) wear was also reported, which limits the use of DMLS tool for EDM machining and it has been found out that porosity (which was about 20 per cent) was one of the primary cause. Research limitations/implications This paper was focused on understanding the effects of important EDM parameters on three performance characteristics (TWR, MRR and surface roughness). While this study identifies that DMLS electrode wear rate is high and porosity could be one of the main cause, presently it does not cover the investigations on reducing the porosity level and its implications. Practical implications The DMLS material had shown huge potential to be used as EDM electrode. The current investigation established a structured experimental approach to understand the effects of EDM parameters on multi response characteristics. The results derived from this study helps to focus future research on two aspects including enriching the copper content and reducing the porosity level, thereby the benefits of lead time reduction in EDM electrode making could be realized. Originality/value The previous research attempts were not focussed on optimising the EDM machining process using rapid tooling electrodes. With the best of author's knowledge none of the researchers have reported these aspects especially for DMLS electrodes. Application of grey relational analysis for performance evaluation of rapid tooling‐based EDM electrodes (DMLS electrodes) appear to be completely new.

The Optimization Study Of Parameters On Edm Machining Micro And Small Holes

Parameter Optimization of Roundness Quality Control for Machined Parts Based on Grey relational Analysis

Parameters Optimization for Sustainable Machining of Ti6Al4V Using a Novel High-Speed Dry Electrical Discharge Milling

Optimisation of the Micro and Small Hole EDM Process Based on the Experimental Design

Experimental investigations and process optimization of SKD61 for sinking EDM

Analysis of Multi-Objective Optimization of Machining Allowance Distribution and Parameters for Energy Saving Strategy

Parameters Optimization of Electrical Discharge Machining Process Using Swarm Intelligence: A Review

Optimization of process parameters of powder mixed EDM for high carbon high chromium alloy steel (D2 steel) through GRA approach

Experimental Study and Parameter Optimization on Sustainable and Efficient Machining GH4169 with Rotating Short Arc Milling Method

Optimizing micro-EDM with carbon-coated electrodes: A multi-criteria approach

Parametric Optimization for Quality of Electric Discharge Machined Profile by Using Multi-Shape Electrode

Optimization of EDM Machining of High Carbon High Chromium Steel Using Zirconium and Nickel Powder Mixed Dielectric by Grey Relational Analysis

Performance Analysis and Optimization of Different Electrode Materials and Dielectric Fluids on Machining of High Carbon High Chromium Steel in Electrical Discharge Machining

Multi response optimization of EDM process parameters for biodegradable AZ31 magnesium alloy using TOPSIS and grey relational analysis

Experimental research and multi-objective optimization of ultrasonic vibration–assisted EDM for Ti6Al4V micro-holes

Multi-Performance Optimization in Electrical Discharge Machining of Al2O3 Ceramics Using Taguchi Base AHP Weighted TOPSIS Method

Process parameters optimization of EDM for hybrid aluminum MMC using hybrid optimization technique

Investigation on Electrical Discharge Machining Parameters of Aluminium7075/Boron Carbide/Titanium Diboride Hybrid Composites by Grey Relational Analysis

Study on the Electrical and Geometrical Parameters of Micro Electrical Discharge Machining

Experimental investigations and optimization of non-electrical parameters during microelectrode fabrication

Optimization of EDM machining parameters using DMLS electrode