Abstract:Purpose The purpose of this paper is to optimise the electro‐discharge machining (EDM) parameters and investigate feasibility of using direct metal laser sintering (DMLS) parts as EDM electrodes. Design/methodology/approach In this paper the effects of discharge current, pulse‐on‐time, flushing pressure are optimized for minimum tool wear rate (TWR), maximum metal removal rate (MRR) and minimum surface roughness (Ra). Taguchi‐based L 9 orthogonal array has been used for performing experiments on EDM machining of EN 24 steel using DMLS electrodes. The grey relational analysis combined with ANOVA techniques have been employed to determine the optimal level as well as their significance. Findings Experimental results have shown that the performance characteristics of the EDM process (TWR, MRR and surface roughness) using DMLS electrode can be quantified and controlled effectively by grey relational approach presented in the study. Current is found to be the most affective parameter in EDM machining using DMLS electrode. Excessive DMLS tool (electrode) wear was also reported, which limits the use of DMLS tool for EDM machining and it has been found out that porosity (which was about 20 per cent) was one of the primary cause. Research limitations/implications This paper was focused on understanding the effects of important EDM parameters on three performance characteristics (TWR, MRR and surface roughness). While this study identifies that DMLS electrode wear rate is high and porosity could be one of the main cause, presently it does not cover the investigations on reducing the porosity level and its implications. Practical implications The DMLS material had shown huge potential to be used as EDM electrode. The current investigation established a structured experimental approach to understand the effects of EDM parameters on multi response characteristics. The results derived from this study helps to focus future research on two aspects including enriching the copper content and reducing the porosity level, thereby the benefits of lead time reduction in EDM electrode making could be realized. Originality/value The previous research attempts were not focussed on optimising the EDM machining process using rapid tooling electrodes. With the best of author's knowledge none of the researchers have reported these aspects especially for DMLS electrodes. Application of grey relational analysis for performance evaluation of rapid tooling‐based EDM electrodes (DMLS electrodes) appear to be completely new.

Experimental investigations and optimization of non-electrical parameters during microelectrode fabrication

Parametric Study of RSM Modelling and Multiresponse Optimization of Milling Electrochemical Spark Micromachining (M-ECSMM) for Microchannel Fabrication on Silicon Wafers

Experimental Investigation and Optimization of Rough EDM of High-Thermal-Conductivity Tool Steel with a Thin-Walled Electrode

Experimental investigations and process optimization of SKD61 for sinking EDM

Machining characteristics and optimization of process parameters in die-sinking EDM of Inconel 625

Optimization of the Material Removal Rate and Electrode Wear Ratio in Electrical Discharge Machining of Reaction-bonded Silicon Carbide by Response Surface Methodology

Experimental Investigation and Optimization of Wire Electrical Discharge Machining for Surface Characteristics and Corrosion Rate of Biodegradable Mg Alloy

EDM Electrode Design and Analysis to Enhance Process Performance

Performance analysis of powder-assisted micro-drilling operation using micro-EDM

Statistical modelling and process optimization of EDM electrode fabricated using pressureless microwave sintering and rapid tooling route

Investigation of micro-electro-discharge machining process parameters during machining of M2 hardened die-steel

Optimization of EDM machining parameters using DMLS electrode

To investigate the effect of discharge energy and addition of nano-powder on processing of micro slots using EDM assisted μ-milling operation

An investigation on the effect of alumina nano powder mixed dielectric oil on EDM-assisted precision micro-drilling operation

Process parameters optimization of EDM for hybrid aluminum MMC using hybrid optimization technique

Performance Analysis and Optimization of Different Electrode Materials and Dielectric Fluids on Machining of High Carbon High Chromium Steel in Electrical Discharge Machining

Study on the Electrical and Geometrical Parameters of Micro Electrical Discharge Machining

Optimization of Machine Process Parameters in EDM for EN 31 Using Evolutionary Optimization Techniques

Optimizing micro-EDM with carbon-coated electrodes: A multi-criteria approach

Multi-objective optimization of an EDM process for Monel K-500 alloy using response surface methodology-multi-objective dragonfly algorithm

Optimization of EDM Machining of High Carbon High Chromium Steel Using Zirconium and Nickel Powder Mixed Dielectric by Grey Relational Analysis