Abstract:Purpose The purpose of this paper is to optimise the electro‐discharge machining (EDM) parameters and investigate feasibility of using direct metal laser sintering (DMLS) parts as EDM electrodes. Design/methodology/approach In this paper the effects of discharge current, pulse‐on‐time, flushing pressure are optimized for minimum tool wear rate (TWR), maximum metal removal rate (MRR) and minimum surface roughness (Ra). Taguchi‐based L 9 orthogonal array has been used for performing experiments on EDM machining of EN 24 steel using DMLS electrodes. The grey relational analysis combined with ANOVA techniques have been employed to determine the optimal level as well as their significance. Findings Experimental results have shown that the performance characteristics of the EDM process (TWR, MRR and surface roughness) using DMLS electrode can be quantified and controlled effectively by grey relational approach presented in the study. Current is found to be the most affective parameter in EDM machining using DMLS electrode. Excessive DMLS tool (electrode) wear was also reported, which limits the use of DMLS tool for EDM machining and it has been found out that porosity (which was about 20 per cent) was one of the primary cause. Research limitations/implications This paper was focused on understanding the effects of important EDM parameters on three performance characteristics (TWR, MRR and surface roughness). While this study identifies that DMLS electrode wear rate is high and porosity could be one of the main cause, presently it does not cover the investigations on reducing the porosity level and its implications. Practical implications The DMLS material had shown huge potential to be used as EDM electrode. The current investigation established a structured experimental approach to understand the effects of EDM parameters on multi response characteristics. The results derived from this study helps to focus future research on two aspects including enriching the copper content and reducing the porosity level, thereby the benefits of lead time reduction in EDM electrode making could be realized. Originality/value The previous research attempts were not focussed on optimising the EDM machining process using rapid tooling electrodes. With the best of author's knowledge none of the researchers have reported these aspects especially for DMLS electrodes. Application of grey relational analysis for performance evaluation of rapid tooling‐based EDM electrodes (DMLS electrodes) appear to be completely new.

Multi response optimization of EDM process parameters for biodegradable AZ31 magnesium alloy using TOPSIS and grey relational analysis

Multi-Objective Optimization Of Edm Process Parameters Using Rsm-Based Gra And Topsis Method For Grade 6 Titanium Alloy

Process parameters optimization of EDM for hybrid aluminum MMC using hybrid optimization technique

Machinability Analysis and Optimization of Electrical Discharge Machining in AA6061-T6/15wt.% SiC Composite by the Multi-criteria Decision-Making Approach

Multi-objective optimization of an EDM process for Monel K-500 alloy using response surface methodology-multi-objective dragonfly algorithm

Optimization of Electrical Discharge Machining of Titanium Alloy (Ti6Al4V) by Grey Relational Analysis Based Firefly Algorithm

Comparative Study on EDM Parameter Optimization for Adsorbed Si3N4–TiN using TOPSIS and GRA Coupled with TLBO Algorithm

Enhancing EDM performance with multi-objective decision-making using copper-coated aluminum electrodes and TOPSIS methodology for Ti-6Al-4V machining

Investigation on Electrical Discharge Machining Parameters of Aluminium7075/Boron Carbide/Titanium Diboride Hybrid Composites by Grey Relational Analysis

Optimization of Machine Process Parameters in EDM for EN 31 Using Evolutionary Optimization Techniques

Optimization of EDM Machining of High Carbon High Chromium Steel Using Zirconium and Nickel Powder Mixed Dielectric by Grey Relational Analysis

Performance Prediction in EDM Process for Al 6061 Alloy Using Response Surface Methodology and Genetic Algorithm

Grey Relational Analysis based Multiresponse Optimization for WEDM of ZE41A Magnesium Alloy

Micro-Edm Of Ti–6Al–4V Using Various Tool Materials: Multi-Response Optimization And Surface Characterization

Parametric Optimization for Quality of Electric Discharge Machined Profile by Using Multi-Shape Electrode

Machining Of Inconel-825 Superalloy With Magnetic Field Assisted Electrical Discharge Turning: A Optimization Approach Using Response Surface Methodology And Multi-Objective Genetic Algorithm

EDM Electrode Design and Analysis to Enhance Process Performance

Surface Modification of Magnesium Alloy AZ91D Using Nanopowder Mixed Electrical Discharge Machining for Biodegradable Implant

Multi-Objective Optimization of the Process Parameters in Electric Discharge Machining of 316L Porous Stainless Steel Using Metaheuristic Techniques

Optimizing dry milling of stir-cast and heat-treated AZ80 magnesium alloy using multiple criteria optimization technique: an experimental study

Optimization of EDM machining parameters using DMLS electrode