Abstract:Abstract Wet anisotropic etching is extensively employed in silicon bulk micromachining to fabricate microstructures for various applications in the field of microelectromechanical systems (MEMS). In addition, it is most widely used for surface texturing to minimize the reflectance of light to improve the efficiency of crystalline silicon solar cells. In wet bulk micromachining, the etch rate is a major factor that affects the throughput. Slower etch rate increases the fabrication time and therefore is of great concern in MEMS industry where wet anisotropic etching is employed to perform the silicon bulk micromachining, especially to fabricate deep cavities and freestanding microstructures by removal of underneath material through undercutting process. Several methods have been proposed to increase the etch rate of silicon in wet anisotropic etchants either by physical means (e.g. agitation, microwave irradiation) or chemically by incorporation of additives. The ultrasonic agitation during etching and microwave irradiation on the etchants increase the etch rate. However, ultrasonic method may rupture the fragile structures and microwave irradiation causes irradiation damage to the structures. Another method is to increase the etching temperature towards the boiling point of the etchant. The etching characteristics of pure potassium hydroxide solution (KOH) is studied near the boiling point of KOH, while surfactant added tetramethylammonium hydroxide (TMAH) is investigated at higher temperature to increase the etch rate. Both these studies have shown a potential way of increasing the etch rate by elevating the temperature of the etchants to its boiling point, which is a function of concentration of etch solution. The effect of various kinds of additives on the etch rate of silicon is investigated in TMAH and KOH. In this paper, the additives which improve the etch rate have been discussed. Recently the effect of hydroxylamine (NH 2 OH) on the etching characteristics of TMAH and KOH is investigated in detail. The concentration of NH 2 OH in TMAH/KOH is varied to optimize the etchant composition to obtain improved etching characteristics especially the etch rate and undercutting which are important parameters for increasing throughput. In this article, different methods explored to improve the etch rate of silicon have been discussed so that the researchers/scientists/engineers can get the details of these methods in a single reference.

Precision Bulk Micromachining Based on KOH Anisotropic Etching Using Ultrasonic Agitation

Study of anisotropic etching of (1 0 0) Si with ultrasonic agitation

Investigation of KOH Anisotropic Etching of Si &gt;100&lt; Wafers for Improving Etched Surface Quality

High speed silicon wet anisotropic etching for applications in bulk micromachining: a review

Novel masked-mask-free etching technology for silicon multilevel microstructures

Dynamic Process of Wet Etching Using BOE Solutions to Control the Etch Rate, Roughness, and Surface Morphology of a Z-cut Α-Quartz Wafer

Wet anisotropic etching characteristics of Si{111} in NaOH-based solution for silicon bulk micromachining

Maskless Etching Of Three-Dimensional Silicon Structures In Koh

Study on maskless etching of silicon symmetric beam-mass structure in aqueous KOH

Method for Fabricating Micro/Nanostructures Via Scanning Probe Microscope and Anisotropic Wet Etching

A novel approach for bulk micromachining of 4H-SiC by tool-based electrolytic plasma etching in HF-free aqueous solution

High Precision Electrochemical Micromachining Based on Confined Etchant Layer Technique

Study on convex-corner undercutting formed by masked-maskless etching in aqueous KOH

A new theory for the anisotropic etching of silicon and some underdeveloped chemical micromachining concepts

High Aspect Ratio Si Etching Technique and Application

Maskless Anisotropic Etching-a Novel Micromachining Technology for Multilevel Microstructures

Enhanced etching characteristics of Si{100} in NaOH-based two-component solution

Optimization of Metal-Assisted Etchant Components for Fabrication of Porous Silicon

Experimental Investigation on Hybrid Technology of Ultrasonic Vibration Assisted Chemo-Mechanical Grinding (CMG) Silicon Wafer

The Formation of Self-Sharpening Nano-Silicon-Tips by Single Step Etching

Uniform Vertical Trench Etching on Silicon with High Aspect Ratio by Metal-Assisted Chemical Etching Using Nanoporous Catalysts.