Abstract:The 7075 aluminium matrix composite reinforced with nano-sized Si C particles was fabricated by ultrasonic assisted semisolid stirring method. The compression mechanical behaviour of the fabricated composite in semisolid state was investigated. The results show that the microstructure of the composite before semisolid compression consists of fine and spheroidal solid grains surrounded by liquid phase.Semisolid compression led to a nonuniform plastic deformation of solid grains. A slight plastic deformation occurred in the locations near the free surface due to the dependence of deformation on liquid flow and flow of liquid incorporating solid grains. However, obvious plastic deformation occurred in the central location and location contacting to die due to the contribution of plastic deformation of solid grains.The true stress–strain curve of the sample compressed at 500 °C consists of rapid increase of true stress and steady stage. However, rapid increase of true stress and decrease of true stress and steady stage are involved in the true stress–strain curves of the samples compressed at 550, 560, 570, 580 and 590 °C.The true stress–strain curve at 600 °C is similar to that at 500 °C. Apparent viscosity decreases with an increase of shear rate, indicating a shear thinning occurrence. When soaking time increases from 5 min to 15 min, the peak stress and steady stress decrease significantly. A further increase of the soaking time led to a slight change. Peak stress and steady stress increase with increasing volume fraction of Si C particles. A sudden increase or decrease of compression velocity led to a significant increase or decrease of the steady stress. The destruction of the samples compressed at solid state temperature mainly depends on cracks parallel to compression direction. However, the destruction forms of the samples compressed at semisolid temperatures consist of cracks parallel to compression direction and partial collapse. Increasing soaking time led to an obvious change of the destruction forms. Compression velocity affects slightly the macro appearance of the sample compressed at semisolid temperatures.

Mechanical Behavior of LC 4 Alloy in Semisolid State at High Volume Fractions of Solid

Unexpected Dynamic Recrystallization Behavior of Ti-7Cu Alloy in Semi-Solid State

Deformation Mechanism of Compression of 2024 Al Alloy in Semi-Solid State

Deformation Mechanisms of Selective Laser Melted 316l Austenitic Stainless Steel in High Temperature Low Cycle Fatigue

DSC analysis of liquid volume fraction and compressive behavior of the semi-solid Si3N4w/Al–Si composite

Variation of Liquid During Compression of Semi-solid ZK60-RE Alloy at High Solid Content

Mechanical Behavior and Microstructure During Compression of Semi-Solid ZK60-RE Magnesium Alloy at High Solid Content

Deformation Behaviour and Microstructures of Semi-Solid A356.2 Alloy Prepared by Radial Forging Process During High Solid Fraction Compression

The Effect of Initial Microstructure of A356 Alloys on the Mechanical Behavior in the Semisolid State

Semi-solid compression of 2A14 alloy with high solid fraction: rheology, constitutive equation and microstructure

Structural Evolution of LC 4 Alloy in Making Thixotropic Billet by SIMA Method

Compressive Rheological Behavior and Microstructure Evolution of a Semi-Solid CuSn10P1 Alloy at Medium Temperature and Low Strain

Compressive Behavior of Liquid Phase Sintered 90 W-7Ni-3Fe Heavy Alloy at High Temperature and Low Strain Rate Condition

High Strain Rate Compressive Deformation Behavior of Zr-based Bulk Amorphous Alloy in Supercooled Liquid Region

Microstructure characteristics and strengthening mechanism of semisolid CuSn10P1 alloys

Mechanical Behavior of Al–Zn–Mg–Cu Alloy under Tension in Semi-Solid State

Mechanical Analysis of Semi-Solid Metals Shear Deformation During Compression

Compression Mechanical Behaviour of 7075 Aluminium Matrix Composite Reinforced with Nano-sized SiC Particles in Semisolid State

Deformation Behavior of Aluminum Alloy during Semi-Solid Compression

Microstructure evolution, Cu segregation and tensile properties of CoCrFeNiCu high entropy alloy during directional solidification

Deformation Characteristics and Constitutive Equations for the Semi-Solid Isothermal Compression of Cold Radial Forged 6063 Aluminium Alloy