Abstract:Strengthening reinforced concrete elements with externally bonded prestressed fiber reinforced polymer (FRP) sheets has become a popular reinforcement technology in recent years. However, in practical engineering applications, due to the limitations of construction operation space and the need for specialized design of tensioning and anchoring devices, it is very cumbersome to apply prestressing force to FRP sheets. Therefore, using the recovery effect of shape memory alloys (SMA) to introduce prestressing into FRP sheets can innovate a new approach by combining FRP sheets and SMA wires. In order to study the basic mechanical properties of FRP/SMA composites, carbon fiber reinforced polymer and shape memory alloys were used to make the composite specimens, and uniaxial tensile tests were carried out on them. The mechanical properties such as the stress-strain curve, failure mode, ultimate tensile strength and fracture strain were obtained. The test results show that CFRP sheet exhibits obvious linear elastic behavior in tensile tests. The stress-strain curve of SMA wire can be divided into four stages: the linear elastic stage, yield stage, strengthening stage and failure stage. The fracture strain at failure can reach 7%, which indicates excellent deformation properties. The loading and unloading cycles have little effect on the mechanical properties of SMA wire. With the increase in the loading rate, the 'stress plateau' section of the phase transformation section of the SMA wire hysteresis curve gradually transits to an oblique upward curve. Increasing the pre-strain value within a certain range can improve the resilience of SMA wires. SMA wires with a pre-strain value of 8% can provide a maximum resilience of 514 MPa after heating to the austenitic state. A prediction model for the number of temperature cycles and maximum recovery force of SMA was proposed and validated. According to this model, the SMA wires can still provide stable resilience after 30 cycles. Increasing the amount of wire (volume ratio) can improve the maximum fracture strain and ultimate tensile strength of CFRP/SMA composite specimens, and the more wire is added, the greater the residual strength after fracture. The diameter of the fiber can significantly reduce the maximum fracture strain and ultimate tensile strength of the FRP/SMA composite specimen.

THE THEORITICAL RESEARCH IN THE YIELDING BEHAVIOUR OF TENSILE DEFORMATION IN SHORT FIBER REINFORCED METAL MATRIX COMPOSITE

MODELLING THE YIELD STRENGTH AND DUCTILITY IN COMPOSITE NANOTWINNED COPPER

Mechanical behavior of a fiber end in short fiber reinforced composites

Investigation of elastic modulus and morphology of reinforcement phase on the stress distribution of copper matrix composites

An elastic-plastic cohesive zone model for metal-ceramic interfaces at finite deformations

Dynamic Tensile Behavior of Fiber Reinforced Materials Based on Fiber Layering Modeling

On the Static and Dynamic Properties of Fiber-Reinforced Polymer Composites: A Three-Phase Constitutive Model

A theoretical study on the temperature-dependent yield strength of in-situ particle and whisker hybrid-reinforced metal matrix composites

Proposal and application of a new yield criterion for metal plastic deformation

A cohesive zone model for the elevated temperature interfacial debonding and frictional sliding behavior

Micromechanical analysis of stochastic fiber/matrix interface strength effect on transverse tensile property of fiber reinforced composites

Prediction of Longitudinal Elastic Modulus of Unidirectional Short-Fiber-reinforced Composites

Effect of fiber arrangement on mechanical properties of short fiber reinforced composites

A tensile deformation model for in-situ dendrite/metallic glass matrix composites

Effect of the Yield Criterion of Matrix on the Brittle Fracture of Fibres in Uniaxial Tension of Composites

Finite Element Analysis of Interfacial Stress of Mg-Baced Composites Reinforced with Short Fiber

Experimental Investigation on Strain Rate Effect of High-Performance Fiber Reinforced Cementitious Composites Subject to Dynamic Direct Tensile Loading

Progressive damage modelling and experimental investigation of three-dimensional orthogonal woven composites with tilted binder

An improved tensile deformation model for in-situ dendrite/metallic glass matrix composites

Experimental Study on the Static Behavior and Recovery Properties of CFRP/SMA Composites

Multiscale Thermomechanical Modeling of Short Fiber-Reinforced Composites