High Speed Integrated Acousto-Optic Switch with High Extinction Ratio

Dai Enguang,Wu Deming,Xu Anshi

DOI: https://doi.org/10.1109/ofc.2000.868265

2000-01-01

Abstract:The technology of single phase unidirectional transducer and focused transducer was adopted for the design of acousto-optic switch. The extinction ratio up to 32 dB and switching speed at 300 ns was achieved.

What problem does this paper attempt to address?

Ultrahigh speed semiconductor all-optical switching

Xu ZHAO,Ming-hua WANG

DOI: https://doi.org/10.13756/j.gtxyj.2001.01.015

2001-01-01

Abstract:The paper presents the sorts, features and applications of semiconductor all-optical switches. According to their structures, the switches can be divided into planar-type and waveguide-type. According to their operation principles, they can be divided into phase-shift-type and frequency-shift-type. The high efficiency of all-optical switching has been proved in 100 Gbit/s optical transmission experiment.
Ring-resonator-assisted Optical Switch with High Extinction Ratio

Fan Wang,Xiang Wang,Haifeng Zhou,Simiao Xiao,Xiaoqing Jiang,Jianyi Yang,Minghua Wang

DOI: https://doi.org/10.1117/12.803927

2008-01-01

Abstract:This paper presents a novel micro-ring-resonator-assisted structure as an optical switch. This device couples two outputs of a 1x2 power splitter into a micro-ring resonator (MRR). The double-beam interference will occur in the MRR. If the phase difference between the beams and the coupling coefficients of MRR are set properly, the device can switch the light by applying phase shift on MRR. High extinction ratio or low crosstalk can be achieved, even if the modulation additional loss is large.
High-speed compact silicon digital optical switch with slot structure

Simiao Xiao,Yubo Li,Yinlei Hao,Xiaoqing Jiang,Jianyi Yang

DOI: https://doi.org/10.1016/j.ijleo.2010.06.027

IF: 3.1

2011-01-01

Optik

Abstract:A high-speed compact silicon digital optical switch (DOS) is proposed in this paper. The direct electro-optic effect is applied by filling electro-optic polymer in the void slot of the branches, which compensates the limitation of silicon itself. The crosstalk of about 35dB and the insertion loss of 0.7dB is obtained, the switching speed is less than 1ps, and the whole device length can be shortened to 616μm even using the basic mode-evolving principle and a simple Y-type structure. Analysis also shows that the device has good fabrication tolerance and wavelength independence over the C-band.
The research of acousto-optic switch device for telecommunication

Yang Wenying,Xu Yong,Hou Shaohua,Xiang Yang

DOI: https://doi.org/10.1117/12.323136

1998-01-01

Abstract:A study of acousto-optic deflection addressing switch of 1xN is reported in this paper. The switch device that we have developed consists of a pair of optical waveguide geoidesic lenses, a titled chirped electrode transducer and a Ti : LiNbO3 waveguide on a piece of LiNbO3 substrate in order to achieve the optical deflection addressing function. A single mode fiber and an array of single mode fiber (N) are coupled with the two endfaces of device respectively. The device is a multiplex channel switch. The device working wavelength is 1.55 mu m. The waveguide geodesic lenses are designed by an optimum analytical method. The non-spherical concave lenses are spherical aberrationless in the aperturs of beam. That is fabricated in single point diamond turning method. The titled chirped electrode transducer bandwide was designed 200MHZ. The experiment at 0.633 mu m He-Ne light source show that the results coincide with the theoretical design. The insertion losses of the device is 8dB about and the channel's crosstalk is better than-20dB. Switch has a broad range of applications. Currently, the most promising applications are in the fields of lightwave communications and optical signal processing.
Fano-resonance-based Mach-Zehnder Optical Switch Employing Dual-Bus Coupled Ring Resonator As Two-Beam Interferometer.

Fan Wang,Xiang Wang,Haifeng Zhou,Qiang Zhou,Yinlei Hao,Xiaoqing Jiang,Minghua Wang,Jianyi Yang

DOI: https://doi.org/10.1364/oe.17.007708

IF: 3.8

2009-01-01

Optics Express

Abstract:A kind of Mach-Zehnder optical switch with a dual-bus coupled ring resonator as a two-beam interferometer is proposed and investigated. The analysis based on the transfer matrix method shows that a sharp asymmetric Fano line shape can be generated in the transmission spectra of such a configuration, which can be used to significantly reduce the phase change required for switching. Meanwhile, it can also be found that complete extinctions can be achieved in both switching states if the structural parameters are carefully chosen and the phase bias is properly set. Through tuning the phase difference between the arms of the Mach-Zehnder interferometer, complete extinction can be easily kept within a large range of the ring-bus coupling ratios in the OFF state. By properly modulating the phase change in the ring waveguide, the shift of the resonant frequency and the asymmetry of the transmission spectra can be controlled to finally enable optical switching with a high extinction ratio, even complete extinction, in the ON state. The switching functionality is verified by the finite-difference time-domain simulation.
A Compact Silicon Nano-Wire Waveguide Optic Switch

T Chu,H Yamada,S Ishida,Y Arakawa

DOI: https://doi.org/10.1109/group4.2005.1516429

2005-01-01

Abstract:Based on silicon nano-wire waveguides, a compact Mach-Zehnder interferometer type optic switch was demonstrated through thermo-optic effect. The maximum extinction ratio was 20-dB, and the switching speed reached 0.1-ms.
High-speed Silicon-Integrated Photonic Radio Frequency Switch Based on Optical Switching.

Hengsong Yue,Haozhe Sun,Tao Chu

DOI: https://doi.org/10.1364/ol.487882

2023-01-01

Abstract:Photonic radio frequency (RF) switches are promising to replace conventional electronic RF switches in modern RF communication systems owing to their high switching speed and immunity to electromagnetic interference. However, existing photonic RF switches are generally based on fre-quency or polarization filtering. Thus, they require more light sources and filters to increase the number of switch-ing channels, consequently limiting scalability. We propose a silicon-integrated photonic RF switch based on optical switching. RF signals are first modulated into the optical domain and switched through phase control of the phase shifters in the optical switch. Switching is not related to the frequency or polarization of the optical carriers, thus reducing the number of light sources required. Experimen-tal results demonstrate 10-GHz switching of two RF signals with frequencies of 20 GHz and 30 GHz. The proposed pho-tonic RF switch can be further expanded to form a large switch matrix, possibly contributing to the development of large-scale RF communication systems. & COPY; 2023 Optica Pub-lishing Group
Ultracompact High‐Extinction‐Ratio Nonvolatile On‐Chip Switches Based on Structured Phase Change Materials

Wenfei Li,Xiyuan Cao,Sannian Song,Longsheng Wu,Ruobing Wang,Yi Jin,Zhitang Song,Aimin Wu

DOI: https://doi.org/10.1002/lpor.202100717

2022-01-01

Laser & Photonics Review

Abstract:Adopting phase change material (PCM) in constructing nonvolatile on-chip photonic switches has received intensive attention recently. Usually, a large-area thin PCM film is directly used to construct a switch. Here, subwavelength structured PCM supporting localized resonance are adopted to efficiently improve the switching performance in a moderate bandwidth to obtain an optimal switch of higher switching contrast, smaller footprint, lower energy consumption, and better structure stability. Such a switch consisting of three cascaded Ge2Sb2Te5 nanodisks with a total volume of only 0.229 mu m(2) x 35 nm on top of a single mode strip silicon waveguide is demonstrated. In the experimental verification, a high extinction ratio up to 27 dB is supported by the fabricated device as a high performance switch. The proposed design methodology will find its great potential in various large-scale integration in optical interconnection and optical computing with new architectures or applications.
Thermo-Optic Switch Based On 2d-Si Photonic Crystals

T Chu,H Yamada,S Ishida,Y Arakawa

DOI: https://doi.org/10.1109/GROUP4.2004.1416726

2004-01-01

Abstract:A Mach-Zehnder interferometer-type optic switch was firstly realized on Si photonic-crystal (PhC) slab structure, by using thermo-optic effect. The maximum extinction ratio was 22 dB, and the switching speed reached 200 mus.
Low Crosstalk 1/spl Times/2 Thermooptic Digital Optical Switch with Integrated S-bend Attenuator

XQ Jiang,W Qi,H Zhang,Y Tang,YL Hao,JY Yang,MH Wang

DOI: https://doi.org/10.1109/lpt.2006.870184

IF: 2.6

2006-01-01

IEEE Photonics Technology Letters

Abstract:We propose and demonstrate a 1 x 2 thermooptic digital optical switch with variable optical attenuators that are integrated with the S-bend waveguides connecting the output of the Y-switch with a standard fiber array. With a total heating power of 140 mW applied to the switch, we have achieved less than -42-dB optical crosstalk. The wavelength response of the switch is flat across the entire C-band. The average polarization-dependent loss of the switch is about 0.49 dB.
Integrated Acousto-Optic Tunable Filter, Equalizer, and Switch in WDM Communication System

EG Dai,DM Wu,AS Xu

DOI: https://doi.org/10.1117/12.370339

1999-01-01

Abstract:Acousto-optic tunable filter (AOTF), acousto-optic switch (AOS) and acousto-optic equalizer with high acousto-optic interaction efficiency are important in WDM networks. The technologies of unidirectional and focused transducer were adopted for the design of integrated acousto-optic device. Extensive usage for the acousto-optic device such as optical switches, gain equalizer and optical add-drop multiplexer have been studied. The concept that changing the radius of focus transducer can adjust the switching speed and FWHM of the filter was proposed for the first time.
Low Crosstalk Y-branch 1×2 Thermo-Optic Digital Optical Switch

Hao ZHANG,Xiao-qing JIANG,Jian-yi YANG,Xi-hua LI,Ming-hua WANG

DOI: https://doi.org/10.3321/j.issn:1005-0086.2005.11.003

2005-01-01

Abstract:We present a polymer Y-branching digital thermo-optic switch with which a variable optical attenuator is integrated. Without any structural extend of the device, it can realize low insertion loss and wide branching angle. By optimizing the design of Y-branching area, a wide-angle low loss Y-branch can be realized. With an applied electrical power of 120 mW, it has a low insertion loss of 0.5 dB and a low crosstalk of -40 dB at 1.55 μm. The polymer digital optical switch (DOS) is attractive in practice due to its compact size, low insertion loss and low power consumption. In addition, it shows good polarization independence and good stability.
Silicon-based digital optical switch with slot structure

Simiao Xiao,Xiang Wang,Fan Wang,Yinlei Hao,Xiaoqing Jiang,Minghua Wang,Jianyi Yang

DOI: https://doi.org/10.1117/12.837467

2009-01-01

Abstract:In this paper a silicon-based digital optical switch (DOS) with the slot structure is demonstrated. By filling electro-optic polymer in the void slot of the branches, the electro-optic effect can be applied to the DOS, and a high-speed silicon switch with digital switching property can be achieved. Analysis shows that the crosstalk is about 35dB, switching speed is less than lps, and the device length is less than 1mm. © 2009 SPIE.
Highly integrated 3×3 silicon thermo-optical switch using a single combined phase shifter for optical interconnects.

Wanjun Wang,Haifeng Zhou,Jianyi Yang,Minghua Wang,Xiaoqing Jiang

DOI: https://doi.org/10.1364/OL.37.002307

IF: 3.6

2012-01-01

Optics Letters

Abstract:We report on an experimental 3 x 3 thermo-optical switch on silicon on insulator. By controlling a single combined phase shifter, light from any input waveguide can be directed to any output waveguide, showing a simple control method and highly integrated structure as compared to the conventional multiway optical switches. Furthermore, the proposed optical switch can be generalized to be a 1 x N and N x N optical switch without an extra phase shifter. The switch is fabricated by complementary metal oxide semiconductor technology. By experiment, full 3 x 3 switching functionality is demonstrated at a wavelength of 1.55 mu m, with an average cross talk of -11.1 dB and a power consumption of 97.5 mW. (C) 2012 Optical Society of America
Design and Performance Analysis of Silica-Based Thermo-Optical Switches Operating in O-Band and C-Band

Shuojian Zhang,Zikang Xu,Guocai Song,Jiahui Yu,Jiasheng Zhao,Junqiang Zhu,Jian-Jun He

DOI: https://doi.org/10.1109/icocn63276.2024.10648576

2024-01-01

Abstract:Integrated silica-based thermo-optical switches operating in O-band and C-band are designed and experimentally demonstrated. Measurement results show high extinction ratios with low driving voltages for both bands.
Research of high speed optical switch based on compound semiconductor

MingHua Wang,Wei Qi,Hui Yu,XiaoQing Jiang,JianYi Yang

DOI: https://doi.org/10.1007/s11434-009-0336-7

2009-01-01

Chinese Science Bulletin

Abstract:High-speed optical switch and its array are the crucial components of all-optical switching system. This paper presents the analytical model of a total-internal-reflection (TIR) optical switch. By employing the carrier injection effect in GaAs and the GaAs/AlGaAs double heterojunction structure, the X-junction TIR switch and the Mach-Zehnder interference (MZI) switch are demonstrated at 1.55 µm. The measured results show that the extinction ratio of both switches exceeds 20 dB. The switching speed reaches the scale of 10 ns.
High‐Speed and Low‐Power 2 × 2 Thermo‐Optic Switch Based on Dual Silicon Topological Nanobeam Cavities

Qiyao Sun,Yingdi Pan,Pan Hu,Songyue Liu,Qi Lu,Hongwei Wang,Lu Sun,Yikai Su

DOI: https://doi.org/10.1002/apxr.202400050

2024-01-01

Abstract:AbstractA 2 × 2 thermo‐optic (TO) switch using dual topological photonic crystal nanobeam (PCN) cavities on the silicon‐on‐insulator (SOI) platform is proposed and experimentally demonstrated. A Fano resonance is observed due to the interference between the topological interface state of the 1D topological PCN cavity and the Fabry‐Perot (F‐P) cavity mode formed between the two facets of the finitely long nanobeam waveguide. Thanks to the sharp rising edge of the spectral response of the Fano resonance and the high confinement of light in the topological PCN cavities, a 2 × 2 TO switch is realized with short switching time and low power consumption. The measured switching power is only 1.55 mW, and the rising time and the falling time are 3 and 5.6 µs, respectively in the on‐off switching experiments. To the best of the knowledge, this is the first time that a dual topological PCN structure is utilized to realize a high‐speed and low‐power TO switch, revealing the possibility of designing high‐performance reconfigurable optical devices and networks using topological photonics.
Ultracompact and low-power-consumption silicon thermo-optic switch for high-speed data

Ruihuan Zhang,Yu He,Yong Zhang,Shaohua An,Qingming Zhu,Xingfeng Li,Yikai Su

DOI: https://doi.org/10.1515/nanoph-2020-0496

IF: 7.5

2020-11-11

Nanophotonics

Abstract:Abstract Ultracompact and low-power-consumption optical switches are desired for high-performance telecommunication networks and data centers. Here, we demonstrate an on-chip power-efficient 2 × 2 thermo-optic switch unit by using a suspended photonic crystal nanobeam structure. A submilliwatt switching power of 0.15 mW is obtained with a tuning efficiency of 7.71 nm/mW in a compact footprint of 60 μm × 16 μm. The bandwidth of the switch is properly designed for a four-level pulse amplitude modulation signal with a 124 Gb/s raw data rate. To the best of our knowledge, the proposed switch is the most power-efficient resonator-based thermo-optic switch unit with the highest tuning efficiency and data ever reported.

optics,physics, applied,materials science, multidisciplinary,nanoscience & nanotechnology
Ultra-low-power consumption silicon electro-optic switch based on photonic crystal nanobeam cavity

Hua Zhong,Jingchi Li,Yu He,Ruihuan Zhang,Hongwei Wang,Jian Shen,Yong Zhang,Yikai Su

DOI: https://doi.org/10.1038/s44310-024-00032-7

2024-08-30

Abstract:Abstract Ultra-low-power consumption and high-speed integrated switches are highly desirable for future data centers and high-performance optical computers. In this study, we proposed an ultra-low-power consumption silicon electro-optic switch based on photonic crystal nanobeam cavities on a foundry platform. The proposed switch showed an ultra-low static-tuning power of 0.10 mW and a calculated dynamic switching power of 6.34 fJ/bit, with a compact footprint of 18 μm × 200 μm. Additionally, a 136-Gb/s four-level pulse amplitude modulation signal transmission experiment was carried out to verify the capability of the proposed electro-optic switch to support high-speed data transmission. The proposed device has the lowest static-tuning power consumption among silicon electro-optic switches and the highest data transmission rate. The results demonstrate the potential applications of this switch in high-performance optical computers, data center interconnects, optical neural networks, and programmable photonic circuits.
Silicon Optical Switch Based On A Tapered W1 Photonic Crystal Waveguide With Thermo-Optic Effect

Qiang Zhao,Kaiyu Cui,Zhilei Huang,Xue Feng,Dengke Zhang,Yidong Huang

DOI: https://doi.org/10.1364/cleo_at.2013.jtu4a.35

2013-01-01

Abstract:Thermo-optic switch based on W1 photonic crystal waveguide is demonstrated, high extinction ratio of 23.5 dB has been experimentally achieved under a switching power as low as 8.9 mW while the device is only 16.8-mu m-long.

High Speed Integrated Acousto-Optic Switch with High Extinction Ratio

Ultrahigh speed semiconductor all-optical switching

Ring-resonator-assisted Optical Switch with High Extinction Ratio

High-speed compact silicon digital optical switch with slot structure

The research of acousto-optic switch device for telecommunication

Fano-resonance-based Mach-Zehnder Optical Switch Employing Dual-Bus Coupled Ring Resonator As Two-Beam Interferometer.

A Compact Silicon Nano-Wire Waveguide Optic Switch

High-speed Silicon-Integrated Photonic Radio Frequency Switch Based on Optical Switching.

Ultracompact High‐Extinction‐Ratio Nonvolatile On‐Chip Switches Based on Structured Phase Change Materials

Thermo-Optic Switch Based On 2d-Si Photonic Crystals

Low Crosstalk 1/spl Times/2 Thermooptic Digital Optical Switch with Integrated S-bend Attenuator

Integrated Acousto-Optic Tunable Filter, Equalizer, and Switch in WDM Communication System

Low Crosstalk Y-branch 1×2 Thermo-Optic Digital Optical Switch

Silicon-based digital optical switch with slot structure

Highly integrated 3×3 silicon thermo-optical switch using a single combined phase shifter for optical interconnects.

Design and Performance Analysis of Silica-Based Thermo-Optical Switches Operating in O-Band and C-Band

Research of high speed optical switch based on compound semiconductor

High‐Speed and Low‐Power 2 × 2 Thermo‐Optic Switch Based on Dual Silicon Topological Nanobeam Cavities

Ultracompact and low-power-consumption silicon thermo-optic switch for high-speed data

Ultra-low-power consumption silicon electro-optic switch based on photonic crystal nanobeam cavity

Silicon Optical Switch Based On A Tapered W1 Photonic Crystal Waveguide With Thermo-Optic Effect