Abstract:Hypothesis: Zirconia microparticles produced by sol-gel synthesis have great potential for photonic applications. To this end, identifying synthetic methods that yield reproducible control over size uniformity is important. Phase transformations during thermal cycling can disintegrate the particles. Therefore, understanding the parameters driving these transformations is essential for enabling high-temperature applications. Particle morphology is expected to influence particle processability and stability. Yttria-doping should improve the thermal stability of the particles, as it does in bulk zirconia. Experiments: Zirconia and YSZ particles were synthesized by improved sol-gel approaches using fatty acid stabilizers. The particles were heated to 1500 °C, and structural and morphological changes were monitored by SEM, ex situ XRD and high-energy in situ XRD. Findings: Zirconia particles (0.4-4.3 μm in diameter, 5-10% standard deviation) synthesized according to the modified sol-gel approaches yielded significantly improved monodispersities. As-synthesized amorphous particles transformed to the tetragonal phase at ∼450 °C with a volume decrease of up to ∼75% and then to monoclinic after heating from ∼650 to 850 °C. Submicron particles disintegrated at ∼850 °C and microparticles at ∼1200 °C due to grain growth. In situ XRD revealed that the transition from the amorphous to tetragonal phase was accompanied by relief in microstrain and the transition from tetragonal to monoclinic was correlated with the tetragonal grain size. Early crystallization and smaller initial grain sizes, which depend on the precursors used for particle synthesis, coincided with higher stability. Yttria-doping reduced grain growth, stabilized the tetragonal phase, and significantly improved the thermal stability of the particles.

Sol-Gel Synthesis of Yttria Stabilized Zirconia Membranes Through Controlled Hydrolysis of Zirconium Alkoxide

Fabrication and Characterization of Y2O3 Stabilized ZrO2 Films Deposited with Aerosol-Assisted MOCVD

Preparation of Yttria Stabilized Zirconia Ultrafiltration Membranes with Inorganic Precursors

Formation and Rate Processes of Y[sub 2]o[sub 3] Stabilized ZrO[sub 2] Thin Films from Zr(DPM)[sub 4] and Y(DPM)[sub 3] by Cold-Wall Aerosol-Assisted MOCVD

Preparation Of Ysz Microporous Membranes On Porous Alpha-Alumina With Metal Chlorides As Precursor

Preparation of Porous YSZ Monoliths via Sol-gel Process Accompanied by Phase Separation

Synthesis of YSZ film by solid single source PE-MOCVD method and characterization

Physical Chemistry of Controlled-Hydrolysis of Propanol Zirconia Doped with Yttrium Nitrite

Synthesis of Monolithic Zirconia with Macroporous Bicontinuous Structure Via Epoxide-Driven Sol–gel Process Accompanied by Phase Separation

Effects of the synthesis hydrogel on the formation of zeolite LTA membranes

Preparation and Characterization of Highly Permeable Porous Yttria-Stabilized Zirconia Hollow Fiber Membrane

Highly permeable porous YSZ hollow fiber membrane prepared using ethanol as external coagulant

Preparation of Zirconia Powders by Sol-gel Process

Internal Nano Voids in Yttria-Stabilised Zirconia (YSZ) Powder

Synthesis and thermal stability of zirconia and yttria-stabilized zirconia microspheres

Preparation of unidirectional porous yttria stabilized zirconia ceramics by an alginate self assemble method

A facile citric acid assisted sol–gel method for preparing monolithic yttria-stabilized zirconia aerogel

Preparation and Characterization of 8mol％ Yttria-stabilized ZrO2 (8YSZ) Fibers Prepared by Sol-Gel Method

The Influences of Additives on the Zirconia Sol-Gel

Polymeric Adsorption Behavior of Nanoparticulate Yttria Stabilized Zirconia and the Deposition of As-Formed Suspensions on Dense Α-Al2o3 Substrates

Preparation and characterization of yttria stabilized zirconia nanoarrays