Abstract:Yttria-stabilized zirconia (YSZ) thin films on polycrystalline substrates were grown by cold-wall aerosol-assisted metallorganic chemical vapor deposition (MOCVD) at the temperatures of 673-1233 K using metal beta-diketonate chelates as precursors. Thin uniform films with amorphous structure were obtained below 673 K; when the deposition temperature increases to 773-1023 K, YSZ films appear to be a mixture of cubic and monoclinic phases; single cubic YSZ phase can be obtained at deposition temperature above 1023 K. The Y/Zr atom ratio estimated from the corresponding X-ray photoelectron spectroscopy peaks is less than the feed ratio, which can be interpreted by different transfer resistance of Y and Zr intermediates diffusing to the substrate surface. The films obtained at 673-1023 K possess a layer structure originated from low mobility of the absorbed species. Along with the increase of the deposition temperature, the grains become mature and larger, and then unite with each other to form a continuous columnar film. Mass transport dominates the growth process within lower temperatures, and homogeneous reaction will interrupt the growth at increasingly high temperatures. Growth rate expression with respect to temperature, pressure, gas flow rate, and metal concentration of precursor solutions was deduced assuming deposition of mass-transport limited mechanism, which is consistent with the experimental results. (c) 2005 The Electrochemical Society. All rights reserved.

Preparation of Yttria Stabilized Zirconia Ultrafiltration Membranes with Inorganic Precursors

Fabrication and Characterization of Y2O3 Stabilized ZrO2 Films Deposited with Aerosol-Assisted MOCVD

Sol-Gel Synthesis of Yttria Stabilized Zirconia Membranes Through Controlled Hydrolysis of Zirconium Alkoxide

Formation and Rate Processes of Y[sub 2]o[sub 3] Stabilized ZrO[sub 2] Thin Films from Zr(DPM)[sub 4] and Y(DPM)[sub 3] by Cold-Wall Aerosol-Assisted MOCVD

Formation and Rate Processes of Y2o3 Stabilized Zro2 Thin Films from Zr(Dpm)(4) and Y(Dpm)(3) by Cold-Wall Aerosol-Assisted Mocvd

Preparation Of Ysz Microporous Membranes On Porous Alpha-Alumina With Metal Chlorides As Precursor

Preparation and Characterization of Highly Permeable Porous Yttria-Stabilized Zirconia Hollow Fiber Membrane

Preparation of Ceramic Ultrafiltration Membrane by Nano-Metal Oxides Modified

Highly permeable porous YSZ hollow fiber membrane prepared using ethanol as external coagulant

Synthesis of YSZ film by solid single source PE-MOCVD method and characterization

Preparation and Characterization of Porous YSZ-Al_2O_3 Comp Osite Membrane

Preparation of unidirectional porous yttria stabilized zirconia ceramics by an alginate self assemble method

Internal Nano Voids in Yttria-Stabilised Zirconia (YSZ) Powder

The preparation of zeolite NaA membranes on the inner surface of hollow fiber supports

Preparation of high-performance zeolite NaA membranes in clear solution by adding SiO2 into Al2O3 hollow-fiber precursor

Preparation of Porous YSZ Monoliths via Sol-gel Process Accompanied by Phase Separation

Zeolite Imidazolate Framework Membranes on Polymeric Substrates Modified with Poly(vinyl Alcohol) and Alginate Composite Hydrogels.

Fabrication of ZIF-8 Membranes on Dual-Layer ZnO-PES/PES Organic Hollow Fibers by In-Situ Crystallization

Ultrasonic-assisted Fabrication of High Flux T-type Zeolite Membranes on Alumina Hollow Fibers

Ethanol-induced formation of precursor for 8mol% Yttria-stabilized zirconia: Towards the production of well-dispersed, easily sintering, and high-conductivity nano-powders

Preparation of zeolite MFI membranes on alumina hollow fibers with high flux for pervaporation