Abstract:The effect of cold rolling and annealing on texture development and mechanical behavior of Zircaloy-4 alloy plates was systematically investigated in the present work. The as-received plates were subjected to cold rolling with thickness reductions of 33% and 66%. Electron back-scatter diffraction and tensile tests were performed to reveal the texture and mechanical properties, respectively. Results showed that a bimodal texture was featured in the as-received plate and the texture was a fiber that spread from <<math>101¯0</math>> to <<math>112¯0</math>>. After cold rolling and annealing, a fiber with a continuous distribution from <<math>101¯0</math>> to <<math>112¯0</math>> and a fiber with a maximum at the <<math>112¯0</math>> position were present in the plates with thickness reductions of 33% and 66%. Besides, the existence of {<math>0001</math>} basal fiber was noticed, indicating more basal poles oriented toward the normal direction. Tensile tests showed that the recrystallized plate with 66% thickness reduction was more ductile and less strong than that with 33% reduction. Meanwhile, tensile properties were sensitive to strain rate, loading direction and thickness reduction. Moreover, the relationship between texture development and yield strength was discussed based on Schmid theory. Calculated results indicated that prismatic <a> slip was the predominant deformation mode and its Schmid factor values under different loading directions contributed to the anisotropy of yield strength. Due to the texture development during cold rolling and annealing, the averaged SF values for prismatic <a> slip changed with the increased thickness reduction, resulting in the variation of yield strength.</a></a>

Microstructures and textures in cold-rolled aluminium strip

Effect of Microstructures on the Anisotropy of the Roll Casting Strip of Cold Rolled 3003 Aluminum Alloy

Mechanical Properties and Texture Evolution During Rolling Process of an AZ31 Mg Alloy

Improved Mechanical Anisotropy and Texture Optimization of a 3xx Aluminum Alloy by Differential Temperature Rolling

Texture, Microstructure and Mechanical Properties of 6111 Aluminum Alloy Subject to Rolling Deformation

Microstructure and texture of Mg alloy sheets fabricated by different rolling methods

Influence of Asymmetric Rolling on the Microstructure, Texture Evolution and Mechanical Properties of Al–Mg–Si Alloy

Microstructure and Texture Evolutions of Aa1050 Aluminum Alloy Cold Rolled to High Strains

Reduction per pass effect on texture traits and mechanical anisotropy of Mg–Al–Zn–Mn–Ca alloy subjected to unidirectional and cross rolling

Enhanced formability of Al–Mg–Si–Zn alloy sheet via dislocation structure and texture during cold rolling

Deformation and Recrystallization Textures in Straight-Rolled and Pseudo Cross-Rolled AA 3105 Aluminum Alloy

Effect of rolling reduction on microstructure, texture, mechanical properties and mechanical anisotropy of AZ31 magnesium alloys

Texture gradient in rough-rolled plate of aluminum alloy 3104 and its effect on annealing textures evolution after hot compression

Texture development and mechanical behavior of Zircaloy-4 alloy plates fabricated by cold rolling and annealing

RELEVANCE OF COLD-ROLLING TECHNOLOGY FOR THE TEXTURE AND ANISOTROPY OF EN AW-8011A ALUMINUM ALLOYS

Microstructure, texture evolution and mechanical anisotropy of Mg-Gd-Y-Zn-Zr alloy sheets produced by unidirectional and cross rolling

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys

Microstructure, texture and mechanical properties of the rolled high modulus Mg-Y-Zn-Al-Li alloy

Texture and microstructure evolution during cold rolling of a strip cast and of a hot rolled austenitic stainless steel

Microstructure and Texture Development in a Thin Gauge Non Oriented Electrical Steel

Microstructure evolution and mechanical properties of Al-Cu-Li alloys with different rolling schedules and subsequent artificial ageing heat treatment