Abstract:The microstructure and texture evolution of a strip cast and of a hot rolled austenitic stainless steel (18% Cr, 8.5% Ni) during cold rolling was studied (maximum thickness reductionΔd/d0= 80%). The microstructure of the hot band was homogeneous through the sheet thickness, except that in the centre layer a small volume fraction of martensite appeared. The hot band texture revealed a through-thickness gradient which was discussed in terms of the shear distribution during hot rolling. The microstructure of the cast strip showed globular grains with martensite in the centre layer and blocks of austenitic dendrites in the other layers. The formation of martensite was attributed to the deformation of the solidified films in the rolling gap. The strip cast sample revealed a weak texture fibre close to {001}〈uvw〉 which was interpreted in terms of growth selection during solidification. During cold rolling in both types of samples the volume fraction of martensite increased up to ≈ 50 vol.% (80% reduction). The cold rolling texture of the austenite was in both cases characterized by {011}〈211〉 and {011}〈100〉. The cold rolling texture of the hot band was stronger than that of the strip cast sample which was attributed to the influence of the starting texture and of the grain size. The cold rolling texture of the austenite was simulated by means of a Taylor type model considering grain interaction and the so-called card glide mechanism. The martensite texture was characterized by {211}〈011〉 and {111}〈211〉. The former component was interpreted in terms of the relaxation of shear constraints. The latter was attributed to selective phase transformation of {011}〈211〉 (austenite) to {332}〈113〉 (martensite) which then rotated towards {111}〈112〉. The rolling textures of the martensite were simulated using a Sachs type deformation model.

Research of Asymmetric and Symmetric Cold Rolling Influence on Microstructure, Mechanical Properties and Stress–Strain State of Steel Strips

Asymmetric Rolling of Interstitial-Free Steel Using Differential Roll Diameters. Part I: Mechanical Properties and Deformation Textures

Strengthening a Medium-Carbon Low-Alloy Steel by Nanosized Grains: The Role of Asymmetrical Rolling

Mechanical anisotropic behavior of low-carbon steel processed by asymmetric rolling

Study on the asymmetric cross rolling of AZ31 magnesium alloy

Elucidating the effects of cold rolling route on the mechanical properties of AISI 316L austenitic stainless steel

Microstructures and textures in cold-rolled aluminium strip

Influence of Asymmetric Rolling on the Microstructure, Texture Evolution and Mechanical Properties of Al–Mg–Si Alloy

Effect of Asymmetric Rolling on the Structure and Properties of Cu-Cr-Zr Alloys

Numerical simulation of cold longitudinal asymmetric rolling process

Effect of Asymmetric Cross Rolling on Microstructure and Mechanical Properties of AZ31 Magnesium Alloy

Friction-mediated tuning of shear deformation and microstructure in asymmetrically rolled Mg–1Gd alloy strips

Study on Asymmetric Rolling Process Applied to Aluminum Alloy Sheets

Characterizing the Shear Deformation during Asymmetric Rolling

Mechanical Properties and Microstructure of a Ti-6Al-4V Alloy Subjected to Cold Rolling, Asymmetric Rolling and Asymmetric Cryorolling

Texture and microstructure evolution during cold rolling of a strip cast and of a hot rolled austenitic stainless steel

Mechanical Properties and Microstructures of Ultrafine-Grained Pure Aluminum by Asymmetric Rolling

Theoretical Study of Asymmetric Bending Force on Metal Deformation in Cold Rolling

Microstructure, texture evolution and mechanical anisotropy of Mg-Gd-Y-Zn-Zr alloy sheets produced by unidirectional and cross rolling

Microstructure and mechanical properties of pure copper plate processed by novel dynamic offsets and shear force adjustment rolling

Cryorolling impacts on microstructure and mechanical properties of AISI 316 LN austenitic stainless steel