Abstract:The morphology of TiC is not difficult to control when the titanium matrix composites with high TiC content are prepared by the melting-casting method. TiC tends to grow into dendrites, increasing the brittleness of the Ti matrix composites. In this study, in-situ TiC-reinforced titanium matrix composites with varying Nb content were prepared by adding Nb. The effects of adding Nb on the microstructure evolution and mechanical properties of the composites were studied. The results show that with the increase of Nb content, the grain size of the composites decreased gradually from 276 μm to 122.8 μm, the primary TiC content decreased, and the eutectic TiC content increased. On the other hand, the orientation relationship between TiC (111)//β-Ti (110) and TiC [10 1 ‾ ]//β-Ti [ 1 ‾ 11] was studied by HTEM. The two-dimensional mismatch of TiC (111)//β-Ti (110) is only 9.06 %, which means that TiC can be used as a nucleation particle of β-Ti. Furthermore, there was a gradual increase in the Rockwell hardness of the composites as the Nb content was incrementally raised from 0 wt% to 1.5 wt%, with the highest recorded value being 47.4 HRC. Notably, when the Nb addition reached 1.0 wt%, the composite achieved its maximum tensile strength of 1352.9 MPa, signifying a 69 % enhancement compared to the absence of Nb. This is due to the combined effect of fine grain strengthening, solution strengthening, and second-phase strengthening in the composites. It introduces a novel approach to regulate the in-situ formation of TiC morphology during the preparation of titanium matrix composites through melting and casting.

MICROSTRUCTURE AND MECHANICAL PROPERTIES OF (Nb,Ti)C-Ni COMPOSITE

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

High pressure sintering behavior and mechanical properties of cBN-Ti 3Al and cBN-Ti 3Al-Al composite materials

Enhanced thermal shock resistance of BN-based composites sintered by hot-pressing with the introduction of nano oxides

Effects of Process Parameters on Microstructure and Properties of TiC Reinforced Cu-Matrix Composites

Microstructures and Enhanced Mechanical Properties of (Zr, Ti)(C, N)-Based Nanocomposites Fabricated by Reactive Hot-Pressing at Low Temperature

Effects of Ni content and sintering temperature on the microstructure and mechanical properties of TiC-Ni composites fabricated by selective carburization of Ti-Ni alloys

Microstructure and Mechanical Properties of Dual Scaled NbC/Ti2AlC Reinforced Titanium–Aluminum Composite

Microstructure, mechanical properties and thermal conductivity of (Ti0.5Nb0.5)C–SiC composites

Effect of Doped Niobium on the Microstructure and Properties of W–Nb/TiC Composites Prepared by Spark Plasma Sintering

Effect of Nb addition on microstructure and mechanical properties of TiC/Ti-7.8Cr composites

Effects of TiB2 Particles on the Microstructure Evolution and Mechanical Properties of B4C/TiB2 Ceramic Composite

Microstructure, mechanical and tribological properties of TiCN nanocomposite films deposited by DC magnetron sputtering

Microstructure and Mechanical Properties of Ti2AlC-reinforced TiAl Composites

Interpenetrating microstructure and fracture mechanism of NiAl/TiC composites by pressureless melt infiltration

Effect of nano-TiC addition on sinterability and mechanical properties of TiC high temperature ceramics

Microstructure And Mechanical Properties Of Sic Ceramic Toughened With Tin Nanoparticles

Investigation of microstructure and irradiation behavior of W–Nb/Ti composites prepared by spark plasma sintering

Microstructure and Mechanical Properties of TiB2-Al2O3 Composites

Microstructure and mechanical properties of TiB 2 -Al 2 O 3 composites

Microstructure and mechanical properties of Zn based composites reinforced by Ti3AlC2