Abstract:A novel segmented control strategy for selenization environment is introduced to regulate the selenization reaction by controlling the evaporation area of Se. This selenization method helps to promote element homogenization, optimize surface smoothness, and obtain a high‐crystalline‐quality absorber with low‐point defects. And the CZTSSe solar cell with a PCE of 13.77% is successfully achieved. High‐crystalline‐quality absorbers with fewer defects are crucial for further improvement of open‐circuit voltage (VOC) and efficiency of Cu2ZnSn(S,Se)4 (CZTSSe) solar cells. However, the preparation of high‐quality CZTSSe absorbers remains challenging due to the uncontrollability of the selenization reaction and the complexity of the required selenization environment for film growth. Herein, a novel segmented control strategy for the selenization environment, specifically targeting the evaporation area of Se, to regulate the selenization reactions and improve the absorber quality is proposed. The large evaporation area of Se in the initial stage of the selenization provides a great evaporation and diffusion flux for Se, which facilitates rapid phase transition reactions and enables the attainment of a single‐layer thin film. The reduced evaporation area of Se in the later stage creates a soft‐selenization environment for grain growth, effectively suppressing the loss of Sn and promoting element homogenization. Consequently, the mitigation of Sn‐related deep‐level defects on the surface and in the bulk induced by element imbalance is simultaneously achieved. This leads to a significant improvement in nonradiative recombination suppression and carrier collection enhancement, thereby enhancing the VOC. As a result, the CZTSSe device delivers an impressive efficiency of 13.77% with a low VOC deficit.

Selenization of mixed metal oxides for dense and ZnSe-free Cu2ZnSnSe4 absorber films

Formation of Alloyed Cu2CoxZn1-xSn(S,Se)4 Absorption Layer and Its Application in Solar Cells.

Formation of Alloyed Cu2Cox Zn1-x Sn(S,Se)4 Absorption Layer and Its Application in Solar Cells

The Preparation of Cu2ZnSnSe4 Films by Selenization of the Oxide Precursors

Preparation and characterization of Cu2ZnSnSe4 thin films by selenization of electrodeposited metal precursors

Fabrication of Cu2ZnSn(S,Se)4 absorber films by selenization of different Cu2ZnSnS4 nanocrystal coatings

Effect of Sn Content in a CuSnZn Metal Precursor on Formation of MoSe2 Film during Selenization in Se+SnSe Vapor

Segmented Control of Selenization Environment for High‐Quality Cu2ZnSn(S,Se)4 Films Toward Efficient Kesterite Solar Cells

Controlling selenization equilibrium enables high-quality Cu2ZnSn(S, Se)4 absorbers for efficient solar cells

Improving the Performance of Solution-Based CZTSSe Absorber by Selenization Annealing with Selenium Powder in Argon

Effects of Selenization on Phase Transition and S/(S+Se) Ratios of As-Deposited Cu2ZnSnS4 Absorbers Sputtered by a Quaternary Target

Compression for Smoothing and Densifying CuInSe2 and Cu2ZnSnSe4 Thin Films Coating from Oxides Nanoparticles Precursor

CZTSe solar cells prepared by electrodeposition of Cu/Sn/Zn stack layer followed by selenization at low Se pressure

An Investigation on Phase Transition for As-Sputtered Cu2ZnSnSe4 Absorbers During Selenization

Formation of Cu2ZnSnSe4 Through Direct Selenization of Metal Oxides

Enhanced solar cell performance of Cu 2 ZnSnSe 4 thin films through structural control by using selenide stacked nanolayers in a non-toxic selenium atmosphere

Nanoparticle Based Preparation Method of Cu_2ZnSn(SSe)_4 Thin Films

Structural and Optical Properties of the Cu2znsnse4 Thin Films Grown by Nano-Ink Coating and Selenization

Suppressing the formation of double‐layer in Cu 2 ZnSnSe 4 ( CZTSe ) absorber layer by facile heating process through nontoxic selenium atmosphere

Effect of Compact Structure on the Phase Transition in the Oxides Derived Cu2ZnSnSe4 Thin Films

Uniform monolayer Cu2ZnSn(S,Se)4 film based on novel precursor solution