Abstract:Experiments have been carried out to study the relationship between the addition of tantalum and microstructure, especially the formation of the B2 phase in lamellar colonies. The mechanical properties, with different contents of Ta, were also measured. Ti46Al8Nb2.6CxTa alloys were prepared by casting with the content of Ta varying from zero to 1.0 at.%. Experimental results show that the B2 phase forms in lamellar colonies with the addition of Ta, and its content increases when the content of Ta increases. Meanwhile, the γ phase decreases and the lattice parameter of the α 2 phase increases. The size of the lamellar colony decreased from 29.9 to 21.6 μm. Ta dissolves into Ti2AlC by substitution, and its solubility is more than 1.1% tested by EDS. Nb, which is necessary for the formation of the B2 phase, comes from two aspects. The first is that Ta dissolves into the Ti2AlC and partly replaces the Nb atom and the second is the decrease in the γ phase because it has higher solid solubility for Nb. The increase in Nb in the liquid phase increases the composition supercooling and heteronucleation at the solidification front, which accounts for refining the lamellar colony. Room temperature compressive testing showed that the compressive strength and the strain increased when the Ta content increased up to 0.8% and then decreased. Improvement of the compressive properties resulted from the grain boundary strengthening and their decrease induced by more content of the B2 phase. Tensile properties, at elevated temperature, were improved with testing temperature increasing from 750 to 950°C, because solid solution strengthening is a major influence factor.

Densification of tantalum carbide ceramics with 5 mol.% Al, Cu, Ag and Au

Effects of Al Addition on Densification, Microstructure and Mechanical Properties of TaC-Al Ceramics

Effects of Tantalum Concentration on the Microstructures and Mechanical Properties of Tungsten-Tantalum Alloys

Effects of Al2O3 content on densification, microstructure, mechanical properties and oxidation resistance of TaC-Al2O3 composites

Microstructure and mechanical properties of TaC ceramics with 1–7.5 mol% Si as sintering aid

Effect of 20 mol% Al addition on phase formation and mechanical properties of TaCx (x=0.5, 0.55, 0.6 and 0.7) ceramics

Controlling Ζ-Ta4c3- Laminate Growth in TaC0.6 Ceramic by Addition of Cu and Its Effect on Mechanical Properties

Sintering and densification mechanisms of tantalum carbide ceramics

Microstructure and Properties of Bulk Ta2AlC Ceramic Synthesized by an in Situ Reaction/hot Pressing Method

Influence of TiC content on microstructure and mechanical properties of (Ta, Ti)C ceramics

Microstructure and mechanical properties of Ta–Ti alloy by plasma-activated sintering

High pressure sintering of fully dense tantalum carbide ceramics with limited grain growth

Microstructure and mechanical properties of the spark plasma sintered Ta2C ceramics

Effects of Tantalum on Microstructure Evolution and Mechanical Properties of High-Nb TiAl Alloys Reinforced by Ti2AlC

Sintering Behavior and Mechanical Properties of Dispersed-Reinforced Fe-TaC Composites Produced by High Energy Ball Milling

New Route to Densify Tantalum Carbide at 1400 °C by Spark Plasma Sintering

Microstructural and high-temperature performance evolution of Al-doped lamellar porous Ti 3 SiC 2 using freeze casting

Effects of TaC Addition on Microstructure and Mechanical Properties of SiBCN Composite Ceramics

Effect of Boron Addition on Microstructure, Mechanical Properties and Oxidation Resistance of TaC Ceramics

Effect of TaC Content on Microstructure and Properties of W-TaC Composites

Processing and Properties of a Low‐fire, High‐thermal‐conductivity Alumina with CuTiNb2O8