Abstract:Experiments have been carried out to study the relationship between the addition of tantalum and microstructure, especially the formation of the B2 phase in lamellar colonies. The mechanical properties, with different contents of Ta, were also measured. Ti46Al8Nb2.6CxTa alloys were prepared by casting with the content of Ta varying from zero to 1.0 at.%. Experimental results show that the B2 phase forms in lamellar colonies with the addition of Ta, and its content increases when the content of Ta increases. Meanwhile, the γ phase decreases and the lattice parameter of the α 2 phase increases. The size of the lamellar colony decreased from 29.9 to 21.6 μm. Ta dissolves into Ti2AlC by substitution, and its solubility is more than 1.1% tested by EDS. Nb, which is necessary for the formation of the B2 phase, comes from two aspects. The first is that Ta dissolves into the Ti2AlC and partly replaces the Nb atom and the second is the decrease in the γ phase because it has higher solid solubility for Nb. The increase in Nb in the liquid phase increases the composition supercooling and heteronucleation at the solidification front, which accounts for refining the lamellar colony. Room temperature compressive testing showed that the compressive strength and the strain increased when the Ta content increased up to 0.8% and then decreased. Improvement of the compressive properties resulted from the grain boundary strengthening and their decrease induced by more content of the B2 phase. Tensile properties, at elevated temperature, were improved with testing temperature increasing from 750 to 950°C, because solid solution strengthening is a major influence factor.

Controlling Ζ-Ta4c3- Laminate Growth in TaC0.6 Ceramic by Addition of Cu and Its Effect on Mechanical Properties

Effect of 20 mol% Al addition on phase formation and mechanical properties of TaCx (x=0.5, 0.55, 0.6 and 0.7) ceramics

Influence of TiC content on microstructure and mechanical properties of (Ta, Ti)C ceramics

Stacking behavior of the close-packed Ta-atom planes and its effects on formation of “hybrid grains” in TaC0.66-0.7 ceramics

Effect of TaC Content on Microstructure and Properties of W-TaC Composites

Tunable mechanical properties and excellent microwave transparent performance of full spectrum (Ti Ta1-)C microcuboids (0 < x < 1) synthesized via a dissolution-precipitation strategy

Evolution of microtexture and performance in TaC/316L composites fabricated by laser powder bed fusion

Effects of Tantalum on Microstructure Evolution and Mechanical Properties of High-Nb TiAl Alloys Reinforced by Ti2AlC

Influence of TaC content on microstructure and mechanical performance of Ti(C,N)-based cermets fabricated by mechanical activation and subsequent in situ carbothermal reduction

β→α Phase Transformation and Properties of Solid-State-Sintered SiC Ceramics with TaC Addition

Effects of Cr3C2, VC, and TaC on Microstructure, WC Morphology and Mechanical Properties of Ultrafine WC–10 wt. % Co Cemented Carbides

Microstructural evolution and mechanical properties of in situ nano Ta4HfC5 reinforced SiBCN composite ceramics

Effect of TaC addition on microstructure and microhardness of additively manufactured tungsten

Low temperature densification mechanism and properties of Ta1-Hf C solid solutions with decarbonization and phase transition of Cr3C2

Sintering and densification mechanisms of tantalum carbide ceramics

Microstructures and properties of in situ (TiB 2p +TiB w )/Cu composites with different Ce content

Grain Refinement and Mechanical Properties of Cu-Cr-Zr Alloys with Different Nano-Sized TiCp Addition.

The Effects of Transition Metal Oxides (Me = Ti, Zr, Nb, and Ta) on the Mechanical Properties and Interfaces of B4C Ceramics Fabricated via Pressureless Sintering

Effect of Ta addition on microstructures, mechanical and damping properties of Cu–Al–Mn–Ti alloy

Influence of TiC Content on Microstructure and Properties of W-3OCu/TiC Composites

Microstructures and mechanical properties of high-entropy (Ti0.2Zr0.2Hf0.2Nb0.2Ta0.2)C ceramics with the addition of SiC secondary phase