Abstract:While the use of low-melting-point metals as sintering aids for high-entropy carbide (HEC) ceramics has been well established, their existence can compromise hardness due to residual metallic inclusions. This study demonstrates an innovative strategy to meet this challenge, where (Ti,Zr,Nb,Ta,Mo)C high-entropy carbide ceramics with ultrafine grains and enhanced hardness are obtained through chromium (Cr)-metal-assisted spark plasma sintering (SPS) at a temperature as low as 1600 degrees C. The results show that the addition of 5 vol% Cr promotes the formation of highly densified single HEC phase ceramics with a high relative density (98.4%) and an ultrafine-grained microstructure (0.17 mu m). This low-temperature densification mechanism can be attributed to Cr's solid-solution effect within the matrix and the increased carbon vacancies generated during sintering. The grain size of the (Ti,Zr,Nb,Ta,Mo)C ceramics with 5 vol% Cr metal addition is significantly smaller than that of Cr-free (Ti,Zr,Nb,Ta,Mo)C ceramics sintered at 2000 degrees C (3.03 mu m) or via traditional low-temperature liquid-phase sintering (1.3-1.5 mu m). Importantly, the addition of 5 vol% Cr substantially increased the hardness of the ceramics, with a remarkable increase from 23.57 to 28.16 GPa compared to that of the pure (Ti,Zr,Nb,Ta,Mo)C ceramics, owing to the fine-grain strengthening and solid-solution strengthening mechanisms. This work highlights the uniqueness of Cr metal as a sintering aid in achieving densification and hardness improvements in (Ti,Zr,Nb,Ta,Mo)C ceramics, offering a promising strategy for improving the properties of HEC materials for further development in the near future.

Sintering and densification mechanisms of tantalum carbide ceramics

High pressure sintering of fully dense tantalum carbide ceramics with limited grain growth

Rapid densification and mechanical properties of ultra-high-pressure sintered transition metal carbide ceramics

Crack tolerant TaC–SiC ceramics prepared by spark plasma sintering

Influence of TiC content on microstructure and mechanical properties of (Ta, Ti)C ceramics

Densification and Mechanical Properties of Tic by Sps-Effects of Holding Time, Sintering Temperature and Pressure Condition

The formation mechanism of in-situ TaC/Ni0.9Ta0.1 composites prepared by pressureless reactive sintering

Pressureless sintering of WC-TaC binderless carbide

Investigation of the microstructure and physical properties of TaSi 2 sintered at high temperature and high pressure

Investigation of TiC formation during ball-milling of elemental titanium and carbon

Pressureless sintering and properties of (Hf0.2Zr0.2Ta0.2Nb0.2Ti0.2)C high-entropy ceramics: The effect of pyrolytic carbon

Microstructural Evolution and Mechanical Properties of Spark Plasma Sintering of Tantalum-Tungsten Alloy

Densification and microstructure evolution of W-TiC-Y2O3 during spark plasma sintering

Effects of Tantalum Concentration on the Microstructures and Mechanical Properties of Tungsten-Tantalum Alloys

Spark plasma sintering of TiC ceramic with tungsten carbide as a sintering additive

Low-temperature densification of high-entropy (Ti,Zr,Nb,Ta,Mo)C—Co composites with high hardness and high toughness

Influence of vanadium content on the microstructural evolution and mechanical properties of (TiZrHfVNbTa)C high-entropy carbides processed by pressureless sintering

Cr-assisted Low-Temperature Densification of (ti,zr,nb,ta,mo)c High-Entropy Carbides with Ultrafine Grain and Enhanced Hardness

Sintering Behavior, Microstructure and Mechanical Properties of Silicon Carbide Ceramics Containing Different Nano-Tin Additive

Sintering Behavior and Mechanical Properties of Dispersed-Reinforced Fe-TaC Composites Produced by High Energy Ball Milling

PRESSURELESS SINTERING OF SILICON CARBIDE NANOCOMPOSITE CERAMICS