Abstract:Ceramic matrix composites are widely studied in the ballistic sector due to their high hardness, fracture toughness, and improved ballistic performance in multilayer shielding systems. However, the presence of dopants in ceramics can pose challenges during processing and potentially compromise the final properties of the sintered material. This study focused on the ceramic processing of Al2O3-based ceramic matrix composites by adding 4 wt.% Nb2O5 (niobium oxide), 0.5 wt.% LiF (lithium fluoride), and 38.5 wt.% TiC (titanium carbide). The composites were produced using cold uniaxial pressing and conventional sintering at 1400 °C for 3 h. The composites were characterized using Archimedes’ principle and scanning electron microscopy (SEM). The results revealed that the samples to which TiC was added exhibited low initial densities, indicating that the applied pressure of 50 MPa during cold pressing was insufficient to adequately densify the green bodies. Moreover, the presence of TiC led to a significant reduction in densification, making it challenging to apply a conductive coating for SEM analysis. Adjustments to the intensity of the electron beam were necessary to conduct the analysis successfully. Conversely, the samples to which TiC was not added exhibited high density values in the green state and yielded consistent results after sintering in line with previous research, indicating a satisfactory degree of sintering in the absence of TiC. These findings highlight the importance of carefully considering the addition of TiC in ceramic matrix composites during processing, which can have a significant impact on densification and subsequent material properties. The results contribute to the understanding of processing parameters with regard to the production of ceramic composites with desirable characteristics for ballistic applications.

Processing and Properties of a Low‐fire, High‐thermal‐conductivity Alumina with CuTiNb2O8

Low-temperature sintering of Al2O3 ceramics doped with 4CuO-TiO2-2Nb2O5 composite oxide sintering aid

Solid-State-Activated Sintering of ZnAl2O4 Ceramics Containing Cu3Nb2O8 with Superior Dielectric and Thermal Properties

Preparation and properties of Al2O3/Al-2(1-0.2)Mg0.2Ti(1+0.2)O5 matrix ceramic composite

Low-Fire Processing and Dielectric Properties of TiO2 with MnOX–CuO

Effects of Alumina on Densification of a Low-Temperature Cofired Crystalllizable Glass+Alumina System

Study of the Aid Effect of CuO-TiO2-Nb2O5 on the Dielectric and Structural Properties of Alumina Ceramics

Mechanical Properties and Oxidation Behavior of Ti-Doped Nb4alc3

Alumina densification at low temperatures using CaV2O6 for LTCC application

Influence of Tic on Density and Microstructure of Al2O3 Ceramics Doped with Nb2O5 and Lif

Fabrication of CaAl12O19‐CaTiO3 composites and their potential usage for TiAl alloy smelting

Sintering Behaviors, Microstructure, and Microwave Dielectric Properties of CaTiO3-LaAlO3 Ceramics Using CuO/B2O3 Additions

Effect of UV irradiation on the densification behavior, microstructure, and microwave dielectric properties of low temperature sintering Al2O3 ceramics

Enhanced thermal conductivity and mechanical performance of CaO–B2O3–SiO2 glass ceramic with AlN addition for LTCC applications

Effect of Al substitution and secondary CuO phase on dielectric response in microwave-processed CaCu3Ti4−xAlxO12 ceramics

Low-Fire Processing (Ca<sub>1−x</sub>Nd<sub>2x/3</sub>)TiO<sub>3</sub>Microwave Ceramics

Low‐Fire Processing (ca1−xnd2x/3)tio3 Microwave Ceramics

Effects of Ti Containing Cu-Based Alloy on Sintering Mechanism, Element Diffusion Behavior and Physical Properties of Glass-Ceramic Bond for Cubic Boron Nitride Abrasive Tool Materials

Sintering and Dielectric Properties of Al2o3 Ceramics Doped by Tio2 and Cuo

Sintering and dielectric properties of Al 2 O 3 ceramics doped by TiO 2 and CuO

The size-effect of Al2O3 on the sinterability, microstructure and properties of glass-alumina composites