Abstract:With the development of wireless communication and Internet-of-Things (IoT), many new communication protocol standards have emerged. IoT micro-hub, which acts as the bridge between ubiquitously deployed IoT terminals and the Internet, is becoming a critical part of IoT [1]. RF transceivers for IoT micro-hub applications are now facing several technical challenges. Firstly, they should be highly re-configurable and flexible to be compatible with a variety of IoT communication protocols. In addition, for long communication distance and complex communication scenarios, there also exists demand to integrate an on-chip power amplifier (PA) into the RF transceiver to reduce cost. Secondly, the number of IoT micro-hubs has increased dramatically with the development of IoT. For lower cost and longer lifetime, there is strong demand to reduce power consumption and chip area of these RF transceivers. A possible solution for IoT micro-hub applications is the software-defined-radio (SDR) transceivers [2]–[4]. However, the high power consumption and large chip area make them not suitable for IoT micro-hub applications. A 0.1-4GHz receiver and 0.1-6GHz transmitter for SDR applications is proposed in [2], but the carrier frequency of receiver is limited to 0.1-4GHz and the noise Figure (NF) is 3-8dB. Though not integrating a phase-locked loop (PLL) or a PA, the chip occupies $8.12\mathrm{mm}^{2}$. A multi-standard transceiver is proposed in [4], in which four parallel low noise amplifiers (LNAs) with several inductors are used in the receiver to cover 0.1-6GHz band, which occupy considerable chip area.

A 780-MHz low power transceiver for wireless nodes applications in Internet of Things

A 11 Mw 2.4 GHz 0.18 Μm CMOS Transceivers for Wireless Sensor Networks

Integrated D-Band Transmitter and Receiver for Wireless Data Communication in 65 Nm Cmos

A CMOS Low Power K-band FMCW Radar Transceiver Front-End for AIOT Application

A 0.6-V Zero-IF/Low-IF Receiver with Integrated Fractional-N Synthesizer for 2.4-Ghz ISM-Band Applications.

Low power high data rate GHz range receiver in 40nm CMOS technology

A 2.85mm 2 RF Transceiver in 40nm CMOS for IoT Micro-Hub Applications

A 5-pJ/Bit OOK Transmitter Using MEMS-Based RF Oscillator for IoT Application in 180-nm CMOS

Ultra-low power, high-data rate, fully on-chip radio frequency on-off keying receiver for internet-of-things applications

A 400mhz 3–10mbps Transceiver IC with ∼0.3 Nj/bit TX/RX Energy Efficiency for Body Area Applications

A 400mhz 3-10mbps Transceiver Ic With Similar To 0.3 Nj/Bit Tx/Rx Energy Efficiency For Body Area Applications

A Single Chain 800m/1.8g/2.4ghz Multistandard Transceiver with Multibranch Transformer for Low-Cost IoT Applications.

A Low-Voltage Multi-Band ZigBee Transceiver

A 75.3 pJ/b Ultra-Low Power MEMS-Based FSK Transmitter in ISM-915 MHz Band for Pico-IoT Applications

A 0.42-Mw 1-Mb/s 3- to 4-Ghz Transceiver in 0.18- $\mu \text{m}$ CMOS with Flexible Efficiency, Bandwidth, and Distance Control for IoT Applications

A Low-Power Monolithic CMOS Transceiver for 802.11b Wireless LANs

A Fully-Integrated 5mW, 0.8Gbps Energy-Efficient Chip-to-Chip Data Link for Ultra-Low-Power IoT End-Nodes in 65-nm CMOS

A Low Cost Integrated Transceiver for Mobile UHF Passive RFID Reader Applications

A Low-Power NB-IoT Transceiver With Digital-Polar Transmitter in 180-nm CMOS.

A 0.66mw 400 MHz/900 MHz Transmitter IC for In-Body Bio-Sensing Applications.

A Low Power Reconfigurable Digital Polar Transmitter for IoT Applications