Adiabatic splitter with velocity and coupling tapered simultaneously

Jiejiang Xing,Kang Xiong,Hao Xu,Zhiyong Li,Xi Xiao,Tao Chu,Jinzhong Yu,Yude Yu

DOI: https://doi.org/10.1109/Group4.2013.6644469

2013-01-01

Abstract:We report an SOI based adiabatic splitter, with velocity and coupling tapered simultaneously. Output uniformity better than 0.2 dB is obtained in 100 nm wavelength range measured, with low excess loss about 0.3 dB. © 2013 IEEE.

What problem does this paper attempt to address?

Broadband and High Uniformity Y Junction Optical Beam Splitter with Multimode Tapered Branch

Chonglei Sun,Jia Zhao,Zuojia Wang,Liuge Du,Weiping Huang

DOI: https://doi.org/10.1016/j.ijleo.2018.12.013

IF: 3.1

2018-01-01

Optik

Abstract:A high uniformity and broad bandwidth Y junction optical beam splitter is proposed and analyzed in this paper based on silicon-on-insulator platform. By replacing the uniform branch with the multimode tapered branch, the bandwidth and the power uniformity of two output ports are unproved prominently. Furthermore, the sensitivity to fabrication accuracy is reduced by widening the splitting angle. The simulation and the experimental results confirm that the bandwidth is larger than 100 nm, the power uniformity of two output ports is enhanced 4 dB, whereas the insertion loss is less than 0.6 dB and the return loss is larger than 26 dB, respectively.
Mid-Infrared, Ultra-Broadband, Low-Loss, Compact Arbitrary Power Splitter Based on Adiabatic Mode Evolution

Jia Xu Brian Sia,Wanjun Wang,Xin Guo,Jin Zhou,Zecen Zhang,Mohamed Said Rouifed,Xiang Li,Zhong Liang Qiao,Chong Yang Liu,Callum Littlejohns,Graham T. Reed,Hong Wang

DOI: https://doi.org/10.1109/jphot.2019.2907788

IF: 2.4

2019-01-01

IEEE Photonics Journal

Abstract:We designed and demonstrated TE-mode arbitrary power splitters based on adiabatic mode evolution. The power splitters are designed with a footprint of smaller than 12 × 2.9 μm2, fabricated on a 400-nm silicon-on-insulator platform, requiring only a single etch step. The optimization process and the conditions for arbitrary-power splitting are performed using three-dimensional-FDTD simulations. We prove this concept through the fabrication of asymmetrical adiabatic evolution-based power splitters with splitting ratios of 50:50, 60:40, and 70:30. The fabricated devices are shown to agree closely with simulation results. Broadband operation with low insertion loss of 0.11–0.6 dB is demonstrated across the 3.66–3.89 μm wavelength range (230 nm). This component has applications in a multitude of areas such as spectroscopic optical sensing and optical phased arrays photonic integrated circuits etc.
Design and Fabrication of the Star Coupler Based on SOI Material

江晓清,李柏阳,唐衍哲,杨建义,王明华,王文辉,杨艺榕,吴亚明,王跃林

IF: 2.56

2003-01-01

Chinese Optics Letters

Abstract:A 1 × 25 star coupler is designed through calculation and beam propagation method (BPM) simulation.Improvement methods are focused on the design of the tapered waveguides in the device, improving theuniformity of the output light power of the star coupler. Utilizing the conventional Si process technology,the device is fabricated based on silicon-on-insulator (SOI) material. The test result shows that the starcoupler has a perfect function of power splitting.
Broadband Multimode 3 Db Optical Power Splitter Using Tapered Couplers.

Weiwei Chen,Jian Lin,Hongxiang LI,Pengjun Wang,Shixun Dai,Yuxiao Liu,Runkui Yao,Jun LI,Qiang Fu,Tingge Dai,Jianyi Yang

DOI: https://doi.org/10.1364/oe.471397

IF: 3.8

2022-01-01

Optics Express

Abstract:A design of a 1 × 2 multimode 3 dB optical power splitter using tapered couplers is proposed and investigated in this paper. As an example, a 1 × 2 splitter processing five-lowest order transverse-electric-polarized modes is designed and optimized by utilizing finite difference time domain method and particle swarm optimization algorithm. To verify the feasibility of this novel design, the optimized device is fabricated on a silicon-on-insulator platform. The coupling lengths of tapered couplers are respectively 6.5 µm, 6.0 µm, 3.5 µm, 5.0 µm, 5.0 µm, 7.5 µm, 6.0 µm, 5.0 µm, and 8.0 µm. Measurement results reveal that, for the fabricated splitter, the power uniformity varies from 0.041 to 0.88 dB, the crosstalk ranges from -23.96 to -14.12 dB, and the insertion loss changes from 0.089 to 1.50 dB within a bandwidth from 1520 to 1600 nm.
Efficient Adiabatic Silicon-on-insulator Waveguide Taper

Yunfei Fu,Tong Ye,Weijie Tang,Tao Chu

DOI: https://doi.org/10.1364/prj.2.000a41

IF: 7.6

2014-01-01

Photonics Research

Abstract:A silicon-on-insulator-based adiabatic waveguide taper with a high coupling efficiency and small footprint is presented. The taper was designed to reduce the incidence of mode conversion to higher-order and radiation modes inside the waveguide. In connecting a 0.5-mu m-wide output waveguide and a 12-mu m-wide input waveguide of a grating coupler, a compact 120-mu m-long taper was demonstrated, achieving a transmission of 98.3%. Previously, this transmission level could only be achieved using a conventional linear taper with a length of more than 300 mu m. (C) 2014 Chinese Laser Press
Compact broadband silicon 3 dB coupler based on shortcuts to adiabaticity.

Defen Guo,Tao Chu

DOI: https://doi.org/10.1364/OL.43.004795

IF: 3.6

2018-01-01

Optics Letters

Abstract:We proposed and experimentally demonstrated a compact, broadband, and low-loss-mode-evolution-based 2 x 23 dB coupler on a silicon-on-insulator platform. The waveguide widths and separations of the coupler were tapered in an optimal manner using the shortcuts to the adiabaticity method. The coupler, with a similar to 70 mu m total length and 200 nm feature size, exhibited <0.3 dB measured excess loss over a broadband wavelength range from 1500 to 1600 nm. Balanced and unbalanced Mach-Zehnder interferometers fabricated for validation showed extinction ratios larger than 27 and 23 dB, respectively, over a 100 nm bandwidth. The extracted splitting ratio was between 0.48 and 0.52. (C) 2018 Optical Society of America
Compact and Low-Loss Silicon Power Splitter Based on Inverse Tapers.

Xianyao Li,Hao Xu,Xi Xiao,Zhiyong Li,Jinzhong Yu,Yude Yu

DOI: https://doi.org/10.1364/ol.38.004220

2013-01-01

Abstract:A compact, low-loss, optical power splitter based on inverse tapers is proposed and fabricated on a silicon-on-insulator platform. High efficiency mode evolution between the fundamental mode of the input waveguide and the super mode of the output waveguides is realized using optimized tapers. A 1×4 splitter with insertion loss lower than 0.4 dB and uniformity better than 0.68 dB in a wavelength range from 1510 to 1550 nm are demonstrated within a footprint of only ∼75 μm2. These properties are very promising for ultrahigh density photonic integration applications.
Adiabaticity Engineered Silicon Coupler With Design-Intended Splitting Ratio

Chih-Hsien Chen,Yu-Fang Lo,Guan-Xun Lu,Yung-Jr Hung,Shuo-Yen Tseng

DOI: https://doi.org/10.1109/jphot.2024.3383439

IF: 2.4

2024-04-10

IEEE Photonics Journal

Abstract:We design and experimentally demonstrate compact and robust adiabaticity engineered couplers (AECs) with design intended splitting ratios (SRs) for the silicon-on-insulator platform. Adiabatic couplers (ACs) with variable SRs can be designed by output waveguide width-differences. By analyzing the mode-evolution region of ACs, we redistribute the adiabaticity parameter by engineering the taper function to obtain fast quasiadiabatic evolution, thus reducing the device footprints. AECs with design-intended SRs exhibit broad bandwidth and robustness against fabrication variations. We experimentally demonstrate compact AECs with average SRs of 22%/78% and 15%/85% with mode-evolution lengths of 42 m and 25 m over a bandwidth of 70 nm, i.e., from 1500 to 1570 for the fundamental transverse electric (TE) mode.

engineering, electrical & electronic,optics,physics, applied
Optical Waveguide Power Splitter with Adjustable Splitting Ratio Using Non-Hermitian Shortcuts to Adiabaticity

Yu-xin Feng,Jin-lei Wu,Bin Ren,Jin-xuan Han,Shuai Tang,Jie Song,Yong-yuan Jiang

DOI: https://doi.org/10.1088/2040-8986/aceb06

IF: 2.1

2023-01-01

Journal of Optics

Abstract:Versatile optical devices with smaller space footprint are crucial for integrated optics. In this work, we design a dual-waveguide power splitter with adjustable splitting ratio depending on the input ports. The modulated gain and loss are imposed on two waveguides to nullify the non-adiabatic coupling using non-Hermitian shortcut to adiabaticity technique. Simulation results reveal that the length of the power splitter can be shortened to about one ninth compared to the one along the adiabatic path, meanwhile, the proposed splitter has good robustness against possible fabrication errors.
A novel polarization and dichroic dual-functional splitter with ultra-high splitting ratios

Kun Li,Fan Lu,Dalin Liu,Zhijun He

DOI: https://doi.org/10.1364/cleo_at.2014.jw2a.47

2014-01-01

Abstract:A novel polarization and dichroic dual-functional splitter is proposed, with ultra-high polarization splitting ratios >33dB and >36dB for TE- and TM-polarized modes, respectively; and with high wavelength splitting ratios >26dB and >33dB for 650nm and 850nm, respectively.
An Asymmetrical Sinx-Based Polarization Beam Splitter at 810 Nm

Shisong Luo,Dongning Liu,Jiaquan Kong,Zengkai Shao,Zeru Wu,Pengfei Xu,Guoxuan Zhu,Yi Wang,Lin Liu,Yanfeng Zhang,Yujie Chen,Siyuan Yu

DOI: https://doi.org/10.1364/acpc.2017.s3d.5

2017-01-01

Abstract:An asymmetrical SiNx-based polarization beam splitter at 810 nm are proposed and fabricated in this work. The simulation results show that the extinction ratio of > 20 dB and the insertion loss of < 0.6 dB can be achieved for both transverse-electric (TE) and transverse magnetic (TM) polarizations at 810 nm.
Ultra-compact and Low-Loss Silicon Polarization Beam Splitter Using a Particle-Swarm-optimized Counter-Tapered Coupler.

Weiwei Chen,Bohao Zhang,Pengjun Wang,Shixun Dai,Wei Liang,Hongxiang Li,Qiang Fu,Jun Li,Yan Li,Tingge Dai,Hui Yu,Jianyi Yang

DOI: https://doi.org/10.1364/oe.408432

IF: 3.8

2020-01-01

Optics Express

Abstract:In this paper, an on-chip silicon polarization beam splitter using a particle-swarm-optimized counter-tapered directional coupler is proposed, designed, and fabricated. The coupling length of the proposed device is only 5 µm. As the waveguide width variation ΔW increases from -20 to 20 nm, the simulated polarization extinction ratio larger than 18.67 dB and the corresponding insertion loss lower than 0.17 dB are achieved. Measured experimental results achieved insertion loss <0.50 dB, TE polarization extinction between 16.68 to 31.87 dB, TM polarization extinction between 17.78 to 31.13 dB, over the wavelength range 1525 to 1600 nm.
Compact and Low-Loss 1 × 3 Polarization-Insensitive Optical Power Splitter Using Cascaded Tapered Silicon Waveguides

Hongxiang Li,Weiwei Chen,Pengjun Wang,Shixun Dai,Yuxiao Liu,Qiang Fu,Jun Li,Yan Li,Tingge Dai,Hui Yu,Jianyi Yang

DOI: https://doi.org/10.1364/ol.401036

2020-01-01

Abstract:In this Letter, a 1 × 3 polarization-insensitive optical power splitter based on cascaded tapered silicon waveguides is proposed and experimentally demonstrated on a silicon-on-insulator platform. By utilizing the particle swarm optimization algorithm and the finite difference time domain method, the structural parameters of the coupling regions are carefully designed to achieve polarization-insensitive property, compact size, low insertion loss, high uniformity, and broad bandwidth. The coupling length can be as short as 7.3 µm. Our measurement results show that, at 1550 nm, the insertion losses of the fabricated device operating in transverse electric (TE) and transverse magnetic (TM) polarizations are, respectively, 0.068 dB and 0.62 dB. Within a bandwidth from 1525 to 1575 nm, the insertion loss is lower than 0.82 dB and the uniformity is less than 1 dB for the fabricated device operating in TE polarization, while the fabricated device operating in TM polarization can have an insertion loss smaller than 1.50 dB and a uniformity lower than 1 dB from 1528 to 1582 nm.
An ultra-broadband, and low loss 3-dB optical power splitter with curved adiabatic taper

Kai Pan,Debin Meng,Yunjie Wang

DOI: https://doi.org/10.1016/j.optcom.2024.130729

IF: 2.4

2024-05-30

Optics Communications

Abstract:Optical power splitter is an essential component for photonics integrated circuits with a variety of applications such as integrated photonic modulators and single-photon detectors. This paper proposes and demonstrates a new design for a 3-dB optical power splitter with curvature optimized adiabatic taper which can achieve ultra-broadband operation, low loss, compact, and fabrication-friendly. The design incorporates a third order Bezier curve to form the adiabatic tapers, with optimized control point positions that effectively enhance waveguide coupling strength while maintaining high transmission efficiency within a compact footprint of and 200 nm minimum feature size. In consequence, simulation results reveal that the design could evenly split the input TE light over an operation bandwidth of 500 nm with an insertion loss (IL) of less than 0.493 dB across 1350 nm to 1850 nm wavelength. A 5-stage cascaded power splitter and a power splitter-based Mach-Zehnder interferometer (MZI) was fabricated for precise measuring. Experimental results demonstrate an average IL of 0.096 dB at 1550 nm, with an IL less than 0.35 dB over the entire measurement range of 1490 nm to 1640 nm. Additionally, the device has a good fabrication tolerance to variations in etching depth, waveguide width, tip width, and sidewall angle.

optics
Ultra-Broadband Polarization Beam Splitter Based On A Tapered Bent Directional Coupler

Ning Zhao,Yu He,Ciyuan Qiu,Yong Zhang,Yikai Su

DOI: https://doi.org/10.1109/acp.2018.8596254

2018-01-01

Abstract:We numerically propose an ultra-broadband polarization beam splitter based on a tapered bent directional coupler. Lower than 1-dB insertion losses and over 10-dB extinction ratios of TE0 mode and TM0 mode are obtained over a wavelength range of 200 nm.
Design of efficient and compact adiabatic couplers based on adiabatic mode evolutions

Tu-Lu Liang,Xi Cheng,Mei Yu,Lingyan Zhang,Jin Shi,Baiyu Wang,Weiwei Rong,Wei Shao

DOI: https://doi.org/10.1016/j.optlastec.2024.110659

IF: 4.939

2024-02-05

Optics & Laser Technology

Abstract:In this study, two different adiabatic couplers are proposed based on the adiabatic mode evolution mechanism in the two-waveguide system. The mode conversion/transfer in vertically asymmetric adiabatic couplers is investigated. The proposed adiabatic couplers couple the beam modes from one waveguide to another using adiabatic mode evolution and enable the mode conversion/transfer between the designed modes. The k -vector frequency-dispersion diagram for the first adiabatic coupler is calculated, and the variation of the guided mode in the adiabatic coupler with the waveguide width is shown to guide the design of adiabatic couplers. The design results demonstrate that the proposed adiabatic mode couplers are substantially shorter than the linear-shape connection, but can achieve the same power mode conversion efficiency. The main function of the first adiabatic mode coupler designed is to convert the TE 0 mode in one port to the TM 0 mode in the other port, the structure only needs a length of 108 μm to achieve 90 % power conversion efficiency, and the traditional linear-shape connection requires 1540 μm to achieve the same conversion efficiency. As a result, the proposed adiabatic coupler size is 14 times shorter than the conventional design. Moreover, in the design of the second 3-dB adiabatic coupler, the adiabatic mode evolution transfer of the two lowest-order even and odd eigenmodes is implemented in a two tapered ridge waveguide system for 3-dB energy splitting. The proposed coupler will achieve a transfer efficiency greater than 90 % in the range of 1400 nm to 3760 nm when the device length is 47.5 μm, which is an ultra-wide operating bandwidth range.

optics,physics, applied
Ultra-broadband and Low-loss Polarization Beam Splitter on Silicon

Chenlei Li,Daoxin Dai,John E. Bowers

DOI: https://doi.org/10.1364/OFC.2020.Th1A.4

2020-01-01

Abstract:We realized a polarization beam splitter with low loss of <1 dB and high extinction ratio of >20 dB in an ultra-broad bandwidth from 1400nm to 1700mn using a pair of cascaded dual-core adiabatic tapers. (C) 2020 The Author(s)
Broadband Polarization Beam Splitter Based on A Tapered Mismatched Directional Coupler

Daigao Chen,Xi Xiao,Lei Wang,Wen Liu,Qi Yang

DOI: https://doi.org/10.1117/12.2240743

2016-01-01

Abstract:We design and fabricate a broadband micro polarization beam splitter on SOI (Silicon-On-Insulator) substrate which is compatible with the 180 nm COMS process. The polarization splitter is based on mismatch coupling in which a tapered directional coupler structure with slowly varying waveguide width is used. The device is fabricated in Astar-IME silicon photonics platform. When the waveguide width of the wider port of the tapered waveguide is fixed at 550 nm, by sweeping the taper waveguide length in several waveguide width of the narrower port, the polarization splitter can realize high extinction ratios of the both polarizations in a broad wavelength range. When the waveguide width of the narrow port is 410 nm, the device can split the TE and TM polarizations in a 30 mu m length with the extinction ratios of the both polarizations more than 15 dB over a wavelength range from 1500 nm to 1600 nm. The proposed polarization beam splitter is not sensitive to the fabrication error and has large tolerance. The polarization extinction ratios are still more than 10 dB in a wavelength range of 100 nm even if the waveguide width of the taper has a 50 nm fabrication error. Due to its simple structure and high performance, we believe this micro polarization beam splitter will be widely used in photonic integrated circuit, optical signal processing, and optical communication devices.
Adiabatic Couplers for Linear Power Division

moustafa mohamed,zheng li,eric dudley,xi chen,li shang,won park,alan r mickelson

DOI: https://doi.org/10.1364/IPRSN.2011.IMD6

IF: 13.582

2011-01-01

Advanced Photonics

Abstract:Adiabatic 3 dB couplers exhibit wide bandwidth and resistance to process and thermal variations. In this work, we investigate tradeoffs between sensitivity and overall length. The discussion includes plans for commercial fabrication.

Adiabatic splitter with velocity and coupling tapered simultaneously

Broadband and High Uniformity Y Junction Optical Beam Splitter with Multimode Tapered Branch

Mid-Infrared, Ultra-Broadband, Low-Loss, Compact Arbitrary Power Splitter Based on Adiabatic Mode Evolution

Design and Fabrication of the Star Coupler Based on SOI Material

Broadband Multimode 3 Db Optical Power Splitter Using Tapered Couplers.

Efficient Adiabatic Silicon-on-insulator Waveguide Taper

Compact broadband silicon 3 dB coupler based on shortcuts to adiabaticity.

Compact and Low-Loss Silicon Power Splitter Based on Inverse Tapers.

Adiabaticity Engineered Silicon Coupler With Design-Intended Splitting Ratio

Optical Waveguide Power Splitter with Adjustable Splitting Ratio Using Non-Hermitian Shortcuts to Adiabaticity

A novel polarization and dichroic dual-functional splitter with ultra-high splitting ratios

An Asymmetrical Sinx-Based Polarization Beam Splitter at 810 Nm

Ultra-compact and Low-Loss Silicon Polarization Beam Splitter Using a Particle-Swarm-optimized Counter-Tapered Coupler.

Compact and Low-Loss 1 × 3 Polarization-Insensitive Optical Power Splitter Using Cascaded Tapered Silicon Waveguides

An ultra-broadband, and low loss 3-dB optical power splitter with curved adiabatic taper

Ultra-Broadband Polarization Beam Splitter Based On A Tapered Bent Directional Coupler

Design of efficient and compact adiabatic couplers based on adiabatic mode evolutions

Ultra-broadband and Low-loss Polarization Beam Splitter on Silicon

Broadband Polarization Beam Splitter Based on A Tapered Mismatched Directional Coupler

Adiabatic Couplers for Linear Power Division