Abstract:In order to achieve desired mechanical properties of alloys by manipulating grain boundaries (GBs) via solute decoration, it is of great significance to understand the underlying mechanisms of microstructural evolution and plastic deformation. In this work, nanocrystalline (NC) Cu-W alloyed films with W concentrations spanning from 0 to 40 at% were prepared by using magnetron sputtering. Thermal stability (within the temperature range of 200 °C-600 °C) and hardness of the films were investigated by using the x-ray diffraction, transmission electron microscope (TEM) and nanoindentation, respectively. The NC pure Cu film exhibited substantial grain growth upon all annealing temperatures. The Cu-W alloyed films, however, displayed distinct microstructural evolution that depended not only on the W concentration but also on the annealing temperature. At a low temperature of 200 °C, all the Cu-W alloyed films were highly stable, with unconspicuous change in grain sizes. At high temperatures of 400 °C and 600 °C, the microstructural evolution was greatly controlled by the W concentrations. The Cu-W films with low W concentration manifested abnormal grain growth (AGG), while the ones with high W concentrations showed phase separation. TEM observations unveiled that the AGG in the Cu-W alloyed thin films was rationalized by GB migration. Nanoindentation results showed that, although the hardness of both the as-deposited and annealed Cu-W alloyed thin films monotonically increased with W concentrations, a transition from annealing hardening to annealing softening was interestingly observed at the critical W addition of ∼25 at%. It was further revealed that an enhanced GB segregation associated with detwinning was responsible for the annealing hardening, while a reduced solid solution hardening for the annealing softening.

Preparation of Fine-Grained Tungsten Heavy Alloys by Spark Plasma Sintered W–7Ni–3Fe Composite Powders with Different Ball Milling Time

Long-term Ball Milling and Hot Pressing of In-Situ Nanoscale Tungsten Carbides Reinforced Copper Composite and Its Characterization

The Effect of A Small Amount of Tungsten on the Microstructure of Mechanically Alloyed Ag37cu63

Effects of Sintering Temperature on Fine-Grained Tungsten Heavy Alloy Produced by High-Energy Ball Milling Assisted Spark Plasma Sintering

Mechanical Properties and Thermal Shock Performance of W-Y2O3composite Prepared by High-Energy-rate Forging

Microstructure and mechanical properties of fine-grained W-7Ni-3Fe heavy alloy by spark plasma sintering

Effect of High-Energy Ball Milling Time on the Density and Mechanical Properties of W-7%Ni-3%Fe Alloy

Ultrafine Grain Tungsten Heavy Alloys with Excellent Performance Prepared by Spark Plasma Sintering

Fabrication of nanocrystalline supersaturated W–Al alloys with enhanced thermal stability and high sinterability

Effect of High‐Energy Ball‐Milling Duration on Densification, Microstructure, and Mechanical Properties of Cr2AlC‐Dispersed 90W‐6Ni‐2Fe‐2Co Heavy Alloys

A Tungsten Heavy Alloy with Enhanced Performance Prepared by Spark Plasma Sintering from Fine Spherical Tungsten Powders

Fine-grained 93W-4.9Ni-2.1Fe alloy with ultrahigh yield strength prepared via low temperature sintering of W nanocomposite powder

Ultrafine-Grained Tungsten Heavy Alloy Prepared by High-Pressure Spark Plasma Sintering

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

Simultaneous enhancements of strength and hardness for fine-grained W-NiFeCoCrMn composites

Effects of milling time and sintering temperature on the mechanical properties of 8 wt% WC/AlCoCrFeNiTi 0.5 high entropy alloy matrix composite

Comparative study of the microstructure and phase evolution of FeCoCrNiAl high-entropy alloy-matrix WC nanocomposite powders prepared by mechanical alloying

Achieving fine-grain tungsten heavy alloys by selecting a high entropy alloy matrix with low W grain growth rate

Influence of Ball Milling Processing on the Microstructure and Characteristic of W–Nb Alloy

Fabrication and Characterization of Tungsten Heavy Alloys with High W Content by Powder Metallurgy

Laser melting deposition of fine-grained 90 W-7Ni-3Fe alloys using pre-sintered granulated powder