Abstract:Wafer bonding technology is important for most MEMS devices' packaging, especially for RF-MEMS devices. Different materials systems, such as Au-Sn, Au-In, have been developed for wafer bonding. A new bonding system, using Ag-Sn, is investigated in this paper. Comparing to well developed Au-Sn bonding (typically bonding temperature of 280degC ), Ag-Sn would provide a potentially lower temperature, lower cost wafer-level bonding method. Both cap wafer and bottom wafer were sputtered with thin film Ti/Ni. Ti is the adhesion layer, and Ni is the wettability and barrier layer. Sn/Au was evaporated on Ti/Ni for cap wafer. The cap wafer was patterned by lift-off process. Ag was sputtered on Ti/Ni for bottom wafer. The thickness of Sn and Ag was designed based on the composition ratio of Ag3Sn in the bonding layer. Thin Au film could protect Sn from oxidation. Afterwards the cap wafer and substrate wafer were brought into contact and sent into the bonding machine. Bonding process was performed in a nitrogen environment. Different bonding parameters such as bonding force, bonding temperature, dwell time are studied. During bonding, the Sn melted when the temperature reached the melting point of Sn and the liquid Sn broke up the barrier layer of the intermetallic compound of Au and Sn. Then the liquid Sn wetted and dissolved the Ag layer to form the intermetallic compound Ag3Sn. The growth of such an interfacial Ag3Sn intermetallic compound is a liquid-solid diffusion process. The main compositions of the bonding interface are pure Ag and Ag3Sn intermetallic compound, which was investigated by SEM and ED AX. Shear strength of the as-bonded structure and those after reliability tests were measured by a shear force tester. The reliability tests include pressure cooker test (PCT) and thermal cycling test (TCT). It has been concluded that the Ag- Sn bonding with delicately designed bonding process one of the potential methods for wafer- bonding.

The Monolithic Integration System of Bulk-Si Sensors and Actuators Based on the Au–Au Bonding Technology

Bonding of Aluminum Coated Silicon Wafers Based on Polypropylene Carbonate and As a Multi-Functional Sensor

Investigation of Au/Si Eutectic Wafer Bonding for MEMS Accelerometers

Monolithic Integration of Capacitive Sensors Using A Double-Side Cmos Mems Post Process

Electrical interconnect in MEMS/NEMS devices by Au/a-Si eutectic reaction

Discussion and Analysis of Au/a-Si Contact Resistance in MEMS/NEMS Devices.

Wafer Lever Packaging for Gyroscope by Au/Si Eutectic Bonding

The MEMS-Based Electrochemical Seismic Sensor With Integrated Sensitive Electrodes by Adopting Anodic Bonding Technology

Monolithic integration of micromachined sensors and CMOS circuits based on SOI technologies

A CMOS Compatible Process for Monolithic Integration of High-Aspect-ratio Bulk Silicon Microstructures

Fabrication of SiC MEMS Pressure Sensor by Anodic Bonding

Au-Si Eutectic Bonding Technology for MEMS Device

12 inch MEMS process for sensors implementation and integration

Fabrication of Monolithic Silicon Multi-Sensor on SOI Wafer

Surface Activated Bonding Method Applied in MEMS Pressure Sensor with TSV Structures

High temperature pressure sensor using Cu-Sn wafer level bonding

A Novel Monolithically Integrated Pressure, Accelerometer and Temperature Composite Sensor

Design and implementation of an extremely large proof-mass CMOS-MEMS capacitive tilt sensor for sensitivity and resolution improvement

Monolithic Integration Of Micro-Cantilever With Conditioning Circuits Based On Soi Techniques

Ag-Sn Fluxless Wafer Bonding Technology

Integration of PDMS-infiltrated CNTs and Si bulk-micromachining for monolithic physical sensors application