Abstract:Eutectic microstructures are one of the most common solidification patterns in the binary or multi-component alloy systems. Due to the fine periodic microstructures of the eutectic alloys, the commercial applications of the eutectic alloys can improve the mechanical properties of the castings. The solidification mechanism of eutectic alloys has been widely studied by a lot of experimental works and theoretical analysis over the years. Recently, numerical models were used to study the mechanisms of formation of phase patterns and selection dynamics of the lamellar eutectic, such as phase field (PF) and cellular automaton (CA) model, which can promote the development of eutectic growth theory. Based on the existing CA method for binary primary a phase, a modified cellular automaton (MCA) model was developed for the simulation of binary eutectic growth. In this model, the influence of constitutional and curvature undercooling on the interface morphology was considered. The growth rate of eutectic interface was calculated by the solute conservation at the alpha/liquid and beta/liquid interfaces. The model could simulate the phenomenon of overgrowth, splitting and steady state growth of the eutectic lamellar. CBr4-C2Cl6 eutectic transparent alloy was chosen to validate the model. The simulated results showed that the increasing pulling rate lead to a smaller eutectic lamellar spacing, which had a good agreement with the Jackson-Hunt theory and the experimental results from the literature. Eutectic morphology evolution was simulated under a constant pulling rate and temperature gradient, which showed that the stable lamellar structures existed when the initial lamellar spacing was in a finite range between the minimum stable spacing lambda(m) and the limiting maximum stable spacing lambda(M). A smaller initial lamellar spacing would lead to lamellar annihilation. Conversely, a larger initial lamellar spacing could lead to the lamellar nucleation due to the appearance of solute rich concave at the center of the alpha/liquid interface. Meanwhile, the oscillatory instability of the eutectic lamellar was also reappeared by the MCA model. The MCA model was easily extended to 3D, and the lamellar rod transition during directional solidification was simulated, which showed that the ratio of volume fraction of alpha and beta phase was smaller than 1/pi tend to form lamellar rod transition when the initial lamellar spacing was smaller than lambda(m).

Prediction of the Solidification Path of Al-4.37cu-27.02mg Ternary Eutectic Alloy with A Unified Microsegregation Model Coupled with Thermo-Calc

Phase Field Simulation for Non-Isothermal Solidification of Multicomponent Alloys Coupled with Thermodynamics Database

Non-equilibrium solidification of bulk undercooled Ni–P eutectic alloys

Simulation of the Dendrite Morphology and Microsegregation in Solidification of Al–Cu–Mg Aluminum Alloys

Numerical Simulation of Recalescence of 3-Dimensional Isothermal Solidification for Binary Alloy Using Phase-Field Approach

Multi-component Phase-Field Simulation of Microstructural Evolution and Elemental Distribution in Fe–Cu–Mn–Ni–Al Alloy

Simulation of Isothermal Solidification of Ternary Alloy with Phase-Field Model

Experimental determination of the phase equilibria of aluminum-rich Al−Li−Cu alloys

Effect of Cooling Rate on Solidification Parameters and Microstructure of Al-7Si-0.3Mg-0.15Fe Alloy

Microstructural evolution and microsegregation in directional solidification of hypoeutectic Al−Cu alloy: A comparison between experimental data and numerical results obtained via phase-field model

Thermodynamic Calculation of Al-Cu Eutectic Alloy with Microstructure Simulation Using Phase Field Method

Calculation of Phase Diagrams and Solidification Paths of Al-rich Al−Li−Cu Alloys

Phase-field Simulation of Solidification in Multicomponent Alloys Coupled with Thermodynamic and Diffusion Mobility Databases

Solidification Curves of AlCu, AlMg and AlCuMg Alloys

Phase-Field Simulation of Microsegregation and Dendritic Growth During Solidification of Hypoeutectic Al-Cu alloys

Three Dimensional Numerical Simulation of Solidification Microstructure of Single Phase Alloy

Modelling Of The Thermosolutal Convection And Macrosegregation In The Solidification Of An Fe-C Binary Alloy

Simulation of Eutectic Growth in Directional Solidification by Cellular Automaton Method

Numerical Simulation of Solidified Microstructure of Ternary Al-Si-Mg Alloy Using an Improved Cellular Automaton Method

Thermodynamic description of metastable fcc/liquid phase equilibria and solidification kinetics in Al-Cu alloys

A numerical study of irregular eutectic in Al-Si alloys under a large undercooling