Abstract:In this work, the WC-Cr2(C, N)-Co nanocomposites were synthesized by using the one-pot carbothermal reduction nitridation hydrothermal precursor method. The preparation mechanisms, including phase and morphology evolutions, were investigated by differential thermal analysis (TG-DSC), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and thermodynamic analysis. The results showed that phase evolution, with temperature increasing, follows the sequences of (amorphous phase, WO2.72) → (CoWO4, WO2.72, WO2, CrWO3) → (WO2, CoWO4, Co6W6C, CrWO3) → (W2C, Co3W3C, WC) → (WC, W2C, Co3W3C) → (WC, Co, Co3W3C trace amount). Through comparing different heat treatment conditions, the powder particle size was more easily affected by temperature than holding time. The higher temperatures or longer time holding resulted in the aggregation of powder particles. Finally, WC-Cr2(C, N)-Co nanopowders with about 60 nm were obtained at 1050 °C for 1 h under the N2 flow of 1 L/min with the oxygen content of 0.22 wt% and the free carbon content of 0.19 wt%. The TEM elements mapping revealed that Cr distributes uniformly with WC grains, Co and WC grains are combined well. The surface of WC-Cr2(C, N)-Co determined by XPS is mainly composed of W, Co, Cr, C, N, and O. The spark plasma sintering (SPS) sintered WC-Cr2(C, N)-Co composite shows a nanocrystalline microstructure with the average grain size ∼170 nm, and the excellent comprehensive mechanical properties with the Vickers hardness 1730 Kg·mm−2 and fracture toughness 11.5 MPa·m1/2, respectively.

Synthesis and Characterization of WC—VC—Co Nanocomposite Powders Through Thermal-Processing of a Core—shell Precursor

Tungsten carbide (WC) nanopowders synthesized via novel core–shell structured precursors

Study on the preparation mechanism of novel WC-Cr2(C, N)-Co nanocomposites

Preparation of Core-Shell Polycarbonate/BaSO_4 Submicron Composite Particles

A Novel Method for Direct Synthesis of WC-Co Nanocomposite Powder

Synthesis and Characterizations of Nanocrystalline Wc-Co Composite Powders by A Unique Ball Milling Process

Effect of Co on morphology and preparation of in situ synthesis of WC-Co composite powders

Preparation of Ultra-Fine WC-Co Cermet and Its Wear Behavior

Characterizations of Ball-Milled Nanocrystalline WC–Co Composite Powders and Subsequently Rapid Hot Pressing Sintered Cermets

Preparation of Nanoscale WC Powders by Sol-Gel Synthesis and Carbon Monoxide Carbonization

Using A Cobalt Activator to Synthesize Titanium Carbide (tic) Nanopowders

A New Route For The Preparation Of Tungsten Carbide-Cobalt Nanocomposites

Synthesis Of Ultrafine Wc-Co Composite Powders Under Hydrogen Atmosphere With Insitu Carbon Via A One-Step Reduction-Carbonization Process

Microstructural Characterization of Nanostructured WC-Co Cemented Carbides

Preparation of low binder WC-Co-Ni cemented carbides with fine WC grains and homogeneous distribution of Co/Ni

Novel synthesis of hierarchical tungsten carbide micro-/nanocrystals from a single-source precursor

WC Strengthened W–Cu Nanocomposite Powder Synthesized by In-Situ Reactions

Preparation and characterization of W@WCx composite powder by oxidation-vacuum carbonization process

Processing and Properties of Carbon Nanotubes-Nano-wc-co Composites

Preparation and characterization of high-performance in-situ synthesized WC reinforced nickel-based coatings

WC-VC/Cr3C2 composite powders prepared by a carbothermic reduction-carburization process