Abstract:Composite materials offer numerous advantages in a wide range of applications, including thermoelectrics. Here, semiconductor-metal composites are produced by just blending nanoparticles of a sulfide semiconductor obtained in aqueous solution and at room temperature with a metallic Cu powder. The obtained blend is annealed in a reducing atmosphere and afterward consolidated into dense polycrystalline pellets through spark plasma sintering (SPS). We observe that, during the annealing process, the presence of metallic copper activates a partial reduction of the PbS, resulting in the formation of PbS-Pb-CuxS composites. The presence of metallic lead during the SPS process habilitates the liquid-phase sintering of the composite. Besides, by comparing the transport properties of PbS, the PbS-Pb-CuxS composites, and PbS-CuxS composites obtained by blending PbS and CuxS nanoparticles, we demonstrate that the presence of metallic lead decisively contributes to a strong increase of the charge carrier concentration through spillover of charge carriers enabled by the low work function of lead. The increase in charge carrier concentration translates into much higher electrical conductivities and moderately lower Seebeck coefficients. These properties translate into power factors up to 2.1 mW m-1 K-2 at ambient temperature, well above those of PbS and PbS + CuxS. Additionally, the presence of multiple phases in the final composite results in a notable decrease in the lattice thermal conductivity. Overall, the introduction of metallic copper in the initial blend results in a significant improvement of the thermoelectric performance of PbS, reaching a dimensionless thermoelectric figure of merit ZT = 1.1 at 750 K, which represents about a 400% increase over bare PbS. Besides, an average ZTave = 0.72 in the temperature range 320-773 K is demonstrated.

Effect of Cu powder addition on thermoelectric properties of Cu/TiO 2-x composites

FEM analysis on thermoelectric properties of metal/TiO2-x composites with random distribution of metal powder

Enhanced Thermoelectric Performance of CuGaTe2 Based Composites Incorporated with Graphite Nanosheets

Fabrication of Nanostructured Non-Stoichiometric TiO2-x by Spark Plasma Sintering for Enhancing Its Thermoelectric Properties

Preparation and Characterization of Talc/Nano-Cu Conductive Composite Powder

Influences of Tin Oxide Surface Modification on the Morphology and Performance of Sintered Ag/SnO2 Composite Powders

Enhanced performance of thermoelectric nanocomposites based on Cu12Sb4S13 tetrahedrite

Fabrication of non-stoichiometric titanium dioxide and its thermoelectric properties

Chemical synthesis, characterization and spark plasma sintering of cu and Cu/TiO2 composite powders

Improvement In Thermoelectric Properties Of Non-Stoichiometric Titanium Dioxide By Reduction Treatment

Fabrication of non-stoichiometric titanium dioxide by spark plasma sintering and its thermoelectric properties

Thermoelectric Properties of TiS2-xPbSnS3 Nanocomposites

PbS–Pb–Cu x S Composites for Thermoelectric Application

Enhanced Thermoelectric Performance of Hydrothermal Synthesized Ag Incorporated Cu &Lt;sub>2-X</sub>s Micro/Nano Composites

Effects of Incorporating Pyrite-Analogous CoSe2 on the Thermoelectric Properties of TiS2

Effect mechanism of mono-particles or hybrid-particles on the thermophysical characteristics and mechanical properties of Cu matrix composites

Fabrication And Thermoelectric Properties Of Magneli Phases By Adding Ti Into Tio2

Nonstoichiometric TiO2-x Obtained Via Spark Plasma Sintering: Thermoelectric Properties and First-Principles Calculations

Synergetic Improvement Strategy on Thermoelectric Performance of CuAlO2 Compacts

Joint effect of Bi2O3 and CuO additives in regulating the thermoelectric properties of (Ca0.87Ag0.1Dy0.03)3Co4O9 composite ceramics

Thermoelectric and Mechanical Properties of Nano BaTiO<sub>3</sub> Composited Cu<sub>1.8</sub>S Bulks